User manual X10 MT10A

[. . . ] Mini Timer Owner's Manual Mini Timer MT10A Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Quick Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How to program a timed event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Special programming buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This will turn the buzzer back on in 10 minutes and will do so each time you operate snooze. The alarm can be cancelled by moving the Buzzer switch to "OFF" and back to "ON" (for wake up the next morning). Pressing "Sleep" after turning a Module on will turn it off -15 minutes later. Pressing "Sleep" after turning a Module off will turn it on - 15 minutes later. Multiple presses adds multiples of 15 minutes to your on time (or off time). Used to select whether you want your Mini Timer to control Modules set to Unit Codes 1 thru 4 or 5 thru 8. You can move the selector switch back and forth to achieve instant control of 8 X10 Modules but you will only be able to set times for one group (1 to 4 OR 5 to 8). Battery Light When you first plug in the Mini Timer the display will flash. It will also flash if you have had a power outage and have not installed a 9 volt battery or the battery is dead. 1. Set the mode switch to "Set Clock. " 2. Press the right hand "Time" rocker to advance to the correct time. A quick press on the rocker will advance the time by 1 minute. If you hold the rocker down the display will advance to the correct time faster. If you overshoot, you can use the left hand rocker to go back. Controlling X10 Modules Follow the steps below to make sure you can control your Modules before you program the Mini Timer. 1. Install and set up all of your X10 Modules referring to the instructions included with them. Be sure to turn off the power at the main circuit breaker panel when installing Wall Switch Modules. 2. Set all of your Modules to the same Housecode as you set on the Mini Timer. 3. Set each Module to a Unit Code Between 1 and 4 (or between 5 and 8 if you set the Selector Switch on the Mini Timer to the 5-8 position. ). 4. Set the Mode Switch on the Mini Timer to the "RUN" position. 5. To turn on a particular Module, press the ON rocker key corresponding to the number you set on the Module you want to control. 6. To turn off a particular Module, press the OFF rocker key corresponding to the number you set on the Module you want to control. 6 7 Setting up the Mini Timer To Dim and Brighten lights connected to a Lamp Module or Wall Switch Module, first select the Module by pressing and releasing the ON rocker key for the desired Module, then press the Bright or Dim rocker key. Hold the key pressed until the desired brightness level is reached. To turn on ALL lights connected to Lamp Modules and Wall Switch Modules (with same Housecode as Mini Timer), press the "All Lights On" key. [. . . ] Alternatively, you could program it/them to turn off later. 12 13 Troubleshooting 1. If a particular Module won't go on or off from the rocker keys on the Mini Timer: Check that you have power to the outlet controlling the Module and the switch on the light or appliance is ON. Check that the Unit Code and Housecode on the Module are set correctly. Try plugging the Module and the Mini Timer into the same outlet. [. . . ]