User manual X10 PA5800

[. . . ] However, each telephone or telephone device that is connected to the telephone line draws power from the telephone line. This is referred to as the device's ringer equivalence number, or REN. If more than one telephone or other device is connected to the same line, add up all the RENs. If the total is more than five, the telephones might not ring. [. . . ] It does not cover the additional X10 automation modules which are supplied with their own installation instructions. Installation Locating the Console Dining Room Hallway Living Room Kitchen Study Choose a location for the Personal Assistance Console which is as central as possible in the house, while providing access to a modular telephone jack and an AC outlet. The console may be placed on a shelf or table, or may be fixed to a wall using the optional mounting bracket and screws. 4 5 Installation Console Mounting the console The Personal Assistance Console is designed to be installed free-standing on a table top or shelf. A wall mounting bracket is also available. Installation Pendant Remote Fitting the backup battery Slide off the battery compartment cover and clip a 9V battery onto the battery contacts. Slide the battery into the battery compartment and replace the cover. When AC power is applied the battery LED on the front panel will go out. It is not necessary to disconnect power to the console when fitting or replacing batteries. STOP CALL Registering the Pendant Remote with the Console · Set the slide switch on the Console to INSTALL. The console beeps once to confirm that the pendant has been registered. · Return the console slide switch to the RUN position. Attaching cables A telephone cord terminated at each end in an RJ11 connector is provided for telephone connection. If possible, the console should be connected to its own telephone line to ensure that the line cannot be busy when the console attempts to dial out. For applications where this is not practical, the console may also share a line with an existing telephone using a "T" adapter. Note: The X10 Personal Assistance Console is not designed to operate with an RJ31X type telephone connection. Testing the Pendant Remote · Set the slide switch on the Console to RUN. The console is triggered and the alarm sounds. · Press STOP to cancel the alarm. Note: If the console has already started dialing out, it will finish dialing the current number before canceling the alarm. 6 7 Installation Lamp Module Installation Home Automation Remote ON OFF 1 2 15 13 11 9 UNIT 1 3 5 7 3 4 5 O M K A C E G 6 7 8 I HOUSE M Lamp Module . O . . A. C . . G I 1-8 9-16 Installing the Lamp Module When the console's alarm trips, lamps connected to Lamp Modules set to the same House Code as the console flash on and off. The lamps stop flashing and remain on after about 4 minutes or when STOP is pressed on the Pendant Remote. · Set the House Code dial to match the House Code set on the Personal Assistance Console. · Set the Unit Code dial to an unused code which can be controlled from a remote or plug-in controller as required. · Plug a lamp into the Lamp Module and plug the Lamp Module into a convenient AC outlet, preferably an unswitched one to ensure that the lamp will always operate when the alarm is triggered. Installing the Home Automation Remote The X10 Home Automation Remote works with your Personal Assistance Console to let you control lamps and appliances anywhere in the home. Just set the House Code dial to the same House Code as the Personal Assistance Console and you're ready to go. Using the Home Automation Remote To switch on a lamp or appliance, press the left side of the numbered key that matches the Unit Code on the X10 module being controlled. Press the Bright and Dim keys to adjust the brightness of lamps connected to Lamp Modules or Wall Switch Modules. Move the slide switch to "9-16" to control modules with unit codes 9-16. Local control The Lamp Module includes circuitry to sense the lamp's own on/off switch to turn the lamp on locally. [. . . ] · Make sure the Pendant Remote's battery is good. · Make sure the console has power and the backup battery is good. If you lose your Pendant Remote. If the system trips by itself Intercom Systems Intercom systems which send voice signals over existing electrical wiring may interfere with the ability to control modules from your X10 Personal Assistance system with the intercom in use. If the intercom system has its own separate wiring it will not cause a problem. If the console does not dial out when you press CALL on the Pendant Remote. For help or more information on setup, please visit: http://www. x10. com/support 14 15 ONE YEAR LIMITED WARRANTY X10 WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL. X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY PERIOD AND WITH PROOF OF PURCHASE. [. . . ]