User manual X10 VK54A

[. . . ] 8 IF YOU WANT TO USE YOUR VIDEO SENDER TO TRANSMIT FROM YOUR STEREO SYSTEM ONLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 REMOTE EXTENDER FEATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 TV Channel Switch FCC CAUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. [. . . ] Point the small tubular antenna up if you intend to use the IR Extender feature (See page 10). TV A/V Cable Coaxial Cable DVD Player DBS (S atellite) Receiver Cable Box a) Connections for a TV with A/V OUT jacks. b) Connections for a TV without A/V OUT jacks. 6 7 HOOKING UP THE VIDEO RECEIVER 1. Connect a set of Audio/Video cables to the A/V OUT jacks on the Audio/Video Receiver. Connect the other end to your TV (use Yellow for video, and either L or R channel for audio). Plug the Audio/Video Receiver's Power Supply jack (the larger power supply than the one used for the Sender) into the Audio/Video Receiver and plug the power supply into a 120 volt wall outlet. Turn the Audio/Video Receiver's power switch (on side of unit) on. Set the channel switch to the same letter as you set on the Video Sender, A, B, C, or D. Position the Audio/Video Receiver in a convenient location such as on top of the TV and orient the antenna so that the flat side points in the direction where you set up the Video Sender. IF YOUR TV IS ALREADY HOOKED UP TO A DBS RECEIVER OR OTHER A/V DEVICE If a DBS Receiver or other A/V component is connected to the TV using A/V cables, you can connect the Audio/ Video Receiver to the free LINE IN jacks on the component. If there are no LINE IN jacks, you will need to use a TV antenna splitter as described earlier. IF YOU WANT TO USE YOUR VIDEO SENDER TO TRANSMIT FROM YOUR STEREO SYSTEM ONLY Just hook up the Video Sender using only the red and white jacks for the right and left channels of the audio signal. Leave the yellow (video) jack and COAX cable unconnected. IF YOUR TV DOES NOT HAVE A/V CONNECTORS You can use the supplied coaxial cable to connect the TV OUT socket on the Audio/Video Receiver to the Antenna input on your TV. If you already have an antenna connected to your TV, you will need to use a TV antenna splitter. Set your TV and the TV Channel switch on the Audio/Video Receiver (on bottom) to the same channel (3 or 4). 8 9 THE REMOTE EXTENDER FEATURE If you get a picture but the quality is poor: The Remote Extender feature allows X10 universal remotes to control some models of RCA DBS Receivers from another room. For example, you can change channels on your Satellite Receiver while viewing in another room. To use the Remote Extender Function you need to use the included Remote Extender Cable. Connect this cable to the IR jack on the Video Sender. Connect the other end of the cable to the IR Control input on the RCA DBS Receiver (DBS II or later model). Point the small tubular antenna on the Video Sender up. To operate the controls on the RCA DBS Satellite Receiver from another room, just press the appropriate buttons on the remote (in SAT mode). The remote sends RF signals directly to the Video Sender, even through walls. The Video Sender passes these signals through the Remote Extender cable to the RCA DBS Satellite Receiver. Try different positions for the antennas on the Sender and Receiver. The system usually works best with the flat side of the antennas facing each other (see diagram below). Sometimes, however, reflections and other effects in the home might affect the signal so that some adjustment of either the Sender or Receiver antenna may be necessary to get the best the signal. Point antennas at each other TROUBLESHOOTING If you do not see a picture on your TV: Check that the Sender and the Receiver are on the same letter channel (A, B, C, or D). [. . . ] X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IF RETURNED TO X10 WITHIN THE WARRANTY PERIOD AND WITH PROOF OF PURCHASE. IF SERVICE IS REQUIRED UNDER THIS WARRANTY: 1. CALL 1-800-675-3044, OR VISIT WWW. X10. COM, OR E-MAIL SALES@X10. COM TO OBTAIN A RETURN MERCHANDISE AUTHORIZATION (RMA) NUMBER. RETURN THE DEFECTIVE UNIT POSTAGE PREPAID TO THE ADDRESS BELOW 3. [. . . ]