User manual X10 VK70A

[. . . ] 7 FINE TUNING YOUR SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 FCC CAUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. [. . . ] Adjust the antenna if necessary to aim it in the direction of the TV that you will view the camera on. Set the Housecode dial to a letter between A and P that matches the Housecode dial on the X10 remote controls you want to use it with. Set the Unit Code dial to a number between 1 and 4*. This lets you turn the camera connected to the XM13A on and off by remote control (using X10 remote controls, sold separately). See the owner's manual supplied with X10 remote controls for more details. IF YOUR TV IS ALREADY HOOKED UP TO A DBS RECEIVER OR OTHER A/V DEVICE, OR IF YOUR TV DOES NOT HAVE A VIDEO IN JACK * You can also set the Unit Code for any group of 4 cameras to 5-8, 9-12, or 13-16. If a DBS Receiver or other A/V component is connected to the TV using A/V cables, you can connect the Video Receiver to the free LINE IN jacks on the component. 6 7 FINE TUNING YOUR SYSTEM TROUBLESHOOTING IF YOU DO NOT SEE A PICTURE ON YOUR TV: Check that the Receiver and the Camera are on the same letter channel (A, B, C, or D). On the Receiver the switch is on the bottom. On the Camera the switch is located under the rubber plug on the base of the unit. Make sure you replace the plug afterwards if you intend to use the camera outdoors. There is a power light on the front of the Receiver. Check that the power switch on the side of the Receiver is ON. For single camera systems the power supply for the Camera will normally be on (it powers up on). For Multi-Camera systems you need to purchase a TM751 Transceiver for the remote control to be able to turn Cameras on. When you turn any one on, in a group of 4 on, the others in the group turn off. Groups must be 1-4, 5-8, 9-12, or 13-16. Check that all camera power supplies are set to the same Housecode as the Transceiver and remote control. Verify that your connections to the TV are correct. If you are using the RCA jacks, make sure you are using the appropriate input mode for your TV, try pressing the A-B button or Video button on your TV's remote control to change the input mode (consult your TV's owner's manual, if necessary). If you are using a Coax cable (Model VR31A Receiver only), verify that the Receiver and the TV are on the same channel (3 or 4). If you connected the Receiver to a VCR and then connected the VCR to your TV, you might need to turn the VCR OFF to see the Camera's picture on your TV. Or you might need to turn the VCR on, AND set it to record the picture from the Camera, in order to see the picture on your TV. Or you might need to press the A-B button on your VCR's remote control. Consult your VCR's owner's manual from more information. The system usually works best with the "pip" on the Camera's antenna facing the flat side of the Receiver's antenna (see diagram below). [. . . ] CALL 1-800-675-3044, OR VISIT WWW. X10. COM, OR E-MAIL SALES@X10. COM TO OBTAIN A RETURN MERCHANDISE AUTHORIZATION (RMA) NUMBER. RETURN THE DEFECTIVE UNIT POSTAGE PREPAID TO THE ADDRESS BELOW 3. ENCLOSE A CHECK FOR $4. 00 TO COVER HANDLING AND RETURN POSTAGE. X10 IS NOT RESPONSIBLE FOR SHIPPING DAMAGE. [. . . ]