User manual X10 VK75A

[. . . ] OWNER'S MANUAL XM14A POWER SUPPLY C1 CAM ERA C2 C3 C4 P1 POSITION P2 P3 Cente r P4 Sweep M . O . K . A . C . . E . I. G SCAN XC18A CAMERA Pro gra m Normal CR14A REMOTE ZC15A PAN 'N TILT BASE MODEL VK75A PAN 'N TILT CAMERA SYSTEM INCLUDES ZC15A PAN 'N TILT BASE, XM14A ADDRESSABLE POWER SUPPLY, CR14A REMOTE, AND XC18A CAMERA INTRODUCTION The VK75A includes the ZC15A Pan `n Tilt Camera Base with XM14A remote controlled power supply, the XC18A Wireless Camera, and the CR14A remote control. The wireless camera is attached to the Pan `n Tilt Camera Base. The camera sends the picture and sound to a receiver that you connect to your TV, up to 100 ft. [. . . ] Move the switch at the bottom from Normal to Program. To clear all stored positions: Move the switch at the bottom to Program. Press Center then move the switch back to Normal. C1 C AMERA C2 C4 P2 POS N ITIO C3 P1 Centers the camera. . A . P3 C ente r P4 Swe ep SC AN M . I . G C Normal WITH THE SWITCH SET TO NORMAL: Scans forward or backward thru cameras controlled by C1 thru C4. Hold to step every 6 seconds. Set to the same letter as the Transceiver and camera power supplies. Press P1, P2, P3 or P4 to move to any of the 4 positions stored for the camera. Press Center to center the position for the camera. Press Sweep to sweep through all 4 positions stored for the camera. To stop scanning or movement to a stored position: Press any BLUE key on the remote while the camera is moving to stop the movement. To turn the camera off: Unplug its power supply. For multiple camera systems a Transceiver is required, which then lets you turn the cameras on and off by remote control. If you purchase multiple Pan 'n Tilt Cameras, and purchase a Transceiver (RR501 or TM751) the Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image from each camera in turn on your TV. You connect each camera (up to 4) to its own Pan 'n Tilt Base, plug each one into an Addressable Power Supply, and set each to a different number between 1-4, 5-8, 9-12, or 13-16 10 11 MULTI-CAMERA SYSTEMS STOP!If you only own one Pan 'n Tilt Camera, you don't need to read any further. Buttons P1 thru P4 are used to store 4 position settings for each of the 4 cameras controlled by buttons C1 thru C4. Move the switch at the bottom from Normal to Program. To store the first position for the camera controlled by C1. Press the BLUE buttons to scan to the position you want. To store the second position for the camera controlled by C1. Press the BLUE buttons to scan to the position you want. To store the third position for the camera controlled by C1. Press the BLUE buttons to scan to the position you want. To store the fourth position for the camera controlled by C1. Press the BLUE buttons to scan to the position you want. [. . . ] Pressing P4 within 3 seconds after you power up forces the camera to recenter every 256 sweeps through the positions you have programmed. To cancel the above automatic centering: While the camera is recentering, move the switch on the CR14A remote to Program, press Sweep, and then move the switch back to Normal. To stop the camera from ever recentering automatically: Unplug the camera's power supply, plug it back in, and (within 3 seconds) press Center. If the camera was sweeping when you unplugged it, it will continue to sweep when you plug it back in, so you should press any blue key to stop the sweep before you unplug the Camera. 16 17 12 MONTH LIMITED WARRANTY If the image quality changes as the Ninja base rotates: Since the Ninja rotates the camera, some positions may move the camera's antenna away from the direction of the Video Receiver. [. . . ]