User manual XEROX NUVERA 100MX

[. . . ] November 2012 702P01023 Xerox Nuvera Production ® System and Xerox iGen™ Digital Production Press ® Production Media Cart User Guide Xerox Nuvera® 100/120/144/157 EA Production System Xerox Nuvera® 100/120/144 MX Production System Xerox Nuvera® 200/288/314 EA Perfecting Production System Xerox Nuvera® 200/288 MX Perfecting Production System Xerox® iGen4® Digital Production Press Xerox® iGen™ 150 Digital Production Press ©2012 Xerox Corporation. Xerox®, Xerox and Design®, , iGen4®, iGen™ and Xerox Nuvera® are trademarks of Xerox Corporation in the United States and/or other countries. Other company trademarks are also acknowledged. Document Version: 1. 0 (October 2012) BR3143 Contents Xerox Production Media Cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not allow any part of the Cart to get wet. Never exceed the Cart load capacity of 160 lb. (72. 6 kg) to avoid personal injury and damage to the Cart. Never raise or lower the paper table unless the Cart is on a firm, level, even surface and the casters are in the locked position. Never use shims or other objects to level the Cart. Use extreme caution when raising or lowering the paper table when it is near other objects to avoid personal injury or damage to other objects. Never allow any object, including limbs, to go beneath the paper table to avoid personal injury or damage to other objects as the paper table nears the bottom of its range. Use caution when lowering the paper table to avoid personal injury or damage to objects that may have come between the paper table and base of the unit. Do not operate the Cart when the paper table is elevated. Maximum paper table height for moving while loaded is 600 mm (24 inches). Cleaning Use a clean cloth to clean the HOST belts. Keep the belts clean, dry and free from debris and dirt. 8 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Charging Charging Charging in the Media Cart The Media Cart battery should be charged if the battery meter is outside the green zone on the meter. Battery meter 1. Ensure that power to the Media Cart is switched off. Power switch Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 9 Charging 2. Connect the battery charger to the battery. Connect charger here Battery charger 3. Plug the power cord into the battery charger. Battery charger Power cord 4. Plug the power cord into a proper electrical outlet. Charge the battery for 6-8 hours or until the light on the charger indicates that it is charged. When light is yellow, system is charging. When light turns green, battery is charged. 10 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide Specifications Specifications Production Media Cart size Length: 43. 5 in. (75 kg) Media size Minimum: 7. 0 x 8. 0 in. (177. 8 x 203. 2 mm) Maximum: 14. 33 x 26 in. (364 x 660. 4 mm) Maximum stack capacity 56 gsm – 400 gsm: 270 mm 75 gsm – 2600 sheets Maximum load capacity 160 lbs. (72. 6 kg) Pickup height From XPS low: 210 mm (8. 26 inches) From XPS high: 600 mm (23. 6 inches) From iGen: 103 mm (4. 06 inches) Elevation limits Maximum unload height of stack: 920 mm (36. 2 inches) Minimum unload height of stack: 100 mm (3. 9 inches) Required kit Install the XPS Media Cart Stacking Surface Kit to enable docking with the XPS Stacker Install the iGen Pallet Interface Kit Install the iGen Powered Eject Kit Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide 11 Operating the Xerox Production Media Cart (Nuvera) Docking the Xerox Production Media Cart with the Xerox Nuvera XPS Stacker It is recommended that you first practice docking the Production Media Cart (Cart) without a paper stack loaded. Warning Do not exceed the load capacity of 160 lbs. [. . . ] Powered eject is triggered to eject 2 seconds after the cart is pushed into the docked location. A red colored emergency Stop button is mounted on the machine frame for customer controlled emergency stop. The power eject system will reset itself after an emergency stop. Note The emergency Stop button is located on the front of the iGen stacker module 6. [. . . ]