User manual XEROX WORKCENTRE 5765 5775 5790 USB CARD READER PLUGIN INSTALLATION GUIDE

[. . . ] Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions. Document version 3. 0: September 2011 Table of Contents 1 Introduction Compatibility . . 8 2 Preparation Server Specifications . [. . . ] If you wish to validate the DC against OCSP after validation of the user: d. Check the box for Validate Domain Controller Certificate via OCSP after CAC/PIV User Authentication. Enter the OCSP Server Service URL details. If you wish to validate the DC certificate retrieved as part of the user authentication process against the one stored during installation, check the box for Domain Controller Signature must match uploaded Domain Controller Certificate. 20 Xerox® Smart Card Installation Guide Installation 5. Upload certificates a. Load the DC root and intermediate certificates and the OCSP root and intermediate certificates: b. Select the Link to Security > Trusted Certificate Authorities Page option or select Trusted Certificate Authorities from the menu. At the Trusted Certificates Authorities screen, select Add. d. g. Browse to the previously retrieved certificates and add them one at a time. Select the certificate then select the Upload Certificate Authority button to add each one. Repeat the process until all certificates are installed. Select Close. Xerox® Smart Card Installation Guide 21 Installation 6. Enter the Domain Controller details for the authentication server. · Locate the device being installed and ensure it has been configured. Note: The System Administrator should configure the cards prior to the card reader being installed on the machine. 4 26 Xerox® Smart Card Installation Guide Installation 3. Attach the ferrite bead to the reader cable Note: The ferrite bead should be clipped onto the cable directly behind the connector. Xerox® Smart Card Installation Guide 27 Installation 4. Attach the fasteners to the card reader device · Fasteners have been provided to secure the card reader to the Xerox WorkCentre. · Peel back the fastener backing strip. · Position the fastener on the under-side of the card reader, as shown. · Repeat for each of the fasteners supplied. 28 Xerox® Smart Card Installation Guide Installation 5. Remove the fastener backing strips · When all the fasteners have been attached to the card reader, remove the backing strips on each of the fasteners. Xerox® Smart Card Installation Guide 29 Installation 6. Place the card reader on the Xerox WorkCentre · Gently place the card reader on the Xerox WorkCentre shelf (do not fix in place at this point). · Position the card reader in a suitable location, ensure it does not obstruct the opening of the document handler side cover. · Check the cable has sufficient length to connect to the rear of the network controller. · Once it is in a suitable location, press firmly on the card reader to fix it in place. 30 Xerox® Smart Card Installation Guide Installation 7. Connect the card reader to the Xerox WorkCentre · Insert the USB connection into the slot provided on the rear of the network controller. · Use the cable ties provided to ensure the cabling is neat and tidy. The hardware installation is now complete. Xerox® Smart Card Installation Guide 31 Installation 8. Confirm the installation · When the card reader and the software has been installed and configured, the Card Reader Detected screen displays on the Xerox WorkCentre local user interface. Note: If the card reader is not detected, refer to Troubleshooting Tips on page 37 for information. 32 Xerox® Smart Card Installation Guide Installation Using Smart Card Once the Smart Card has been enabled, each user must insert a valid card and enter their Personal Identification Number (PIN) on the touch screen. When a user has finished using the Xerox WorkCentre, they are then required to remove their card from the card reader to end the session. [. . . ] This process can be repeated to retrieve the Certificates from each of the required servers. Xerox® Smart Card Installation Guide 43 Retrieving the Certificate from a Domain Controller or OCSP Server 44 Xerox® Smart Card Installation Guide Determining the Domain in which your Card is Registered 1. 2. B 3. 4. From your PC, click the Start menu and right click on My Computer. From the drop down list, select Properties. When the System Properties window opens, click on the Computer Name tab. [. . . ]