User manual XEROX XC1000

[. . . ] XC 800, XC1000, XC1200 Series User Guide 701P96454 10/97 Table of Contents Safety Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 How to obtain a French or Spanish User Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Copier Equipment Listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place the original face down and align it with the registration guide on the document glass and close the document cover. XC865/ XC1044/ XC1255 copiers only Unless the SDF auto start has been disabled, the Paper Tray Bypass cannot be selected. Adjust the bypass guide to the width of the copy paper. 2. Insert a single sheet of copy paper into the paper tray bypass. · · The paper will feed automatically. When copying continuously, insert the next copy paper as soon as the previous sheet has fed. 24 Alternate Paper Tray (XC810/ XC1040/ XC1045) The alternate paper tray can be used to feed multiple sheets of standard paper, or it can be used to feed single sheets of special or heavy papers such as note cards, transparencies, and labels. The alternate paper tray holds up to 50 sheets of (standard weight) copy paper ranging in size from 3. 5×5. 5" to 8. 5×14"/ A6 to 216×356mm. Predrilled paper: holes toward the front of the copier. Letterhead paper: face up with the top toward the left. · Use labels and transparencies specifically designed for copiers (high temperatures). Lower the alternate paper tray, located on the right side of the copier. Unfold the paper support extension as shown. 1. Adjust the guides to the width of the copy paper. (continued) 25 Alternate Paper Tray (XC810 / XC1040/ XC1045) 4. Insert the copy paper all the way into the alternate paper tray until it stops (do not force). Note: When loading transparencies or labels insert one sheet at a time. Press the Paper Supply button to select the alternate paper tray. Place the original face down and align it with the registration guide on the document glass and close the document cover, or place it in the SDF. 8. Note: When the Alternate Paper Tray runs out of paper, the green indicator in the copier diagram flashes and the display will show a flashing P. To continue copying, add more paper and press Start. 26 Two-Sided Copying 1. Place side 1 original face down on the Document Glass, with the TOP toward the LEFT. Note: 16 lb / 60 gsm copy paper is not recommended for two-sided copying. Remove the first original and place the second original face down on the Document Glass with the TOP toward the RIGHT, and lower the document cover. Remove side 1 copy from the output tray and insert it face down, TOP toward the RIGHT, into the paper tray bypass / alternate bypass tray. [. . . ] 2. 5 mg/m3 (total dust) XEL2: 0. 4 mg/m3 (respirable dust) TLV: PEL: Additional Information: The results obtained from a Xerox sponsored Chronic Toner Inhalation Study, demonstrated no lung change in rats for the lowest (1mg/m³) exposure level (i. e. the level most relevant to potential human exposure). A very slight degree of fibrosis was noted in 25% of the animals at the middle (4mg/m³) exposure level, while a slight degree of fibrosis was noted in all the animals at the highest (16 mg/m³) exposure level. These findings are attributed to "lung overloading", a generic response to excessive amounts of any dust retained in the lungs for a prolonged period. [. . . ]