User manual XINDAK XA6950

[. . . ] Since the swift development on technology, there may be some outdated description which is not applicable any more, please understand. Our company does not assure that there will be no updating version on this manual when there is no mistake or neglect. If there is any change on the manual, there will be no notice. XA6950 Chapter 1 Important Safety Instruction CAUTION ! Dangerous Voltage The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to presence of uninsulated "Dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Important Instructions ! The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance (servicing) 1 XA6950 Chapter 2 2. 1 Before Use Please read all instructions and precautions carefully and completely before operating your XA6950 Digital D/A Converter. [. . . ] If there is any change on the manual, there will be no notice. XA6950 Chapter 1 Important Safety Instruction CAUTION ! Dangerous Voltage The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to presence of uninsulated "Dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Important Instructions ! The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance (servicing) 1 XA6950 Chapter 2 2. 1 Before Use Please read all instructions and precautions carefully and completely before operating your XA6950 Digital D/A Converter. Always keep this unit out of the reach of children. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus ( including amplifiers) that produce heat. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Unplug this apparatus during lightning storms or when unused for a long time. Always disconnect your entire system from the AC mains before connecting or disconnecting any cable, or when cleaning any component. This product must be terminated with a three conductor AC mains power cord which includes an earth ground connection, to prevent shock hazard, all three connections must always be used. AC extension cords are not recommended for use with this product. There are three output ports available: signal-terminal tube analog RCA output port, OPA analog RCA output port and OPA balanced output port to afford various chooses for the users. The decoding circuit We adopted the latest digital technology, making use of the Delta digital interface which was developed independently by Xindak to upgrade the signal from 16Bit/44. 1KHz to 24bit/96KHz and then accomplish 24Bit/96KHz decoding. Multi-linear power supply circuits We adopted audiophile-level linear power supply circuit. The independent voltage regulating and filtering for each power supply improve the sound quality greatly and make the sound more exquisite and transparent. The two custom-made high quality annular power transformers and independent power supply system on digital and analog parts could greatly reduce the mutual interferences and make the sound purer. We use the advanced CAD technology, Two-sided hole-drilled glass and fiber plate which has excellent high-frequency characteristics and many grounding wires for shielding to reduce various disturbances and improve the Signal to Noise Ratio. 3 XA6950 Chapter 3 3. 2 Block Diagram Introduction U11 DIGITAL TO ANALOG CONVERTER 3. 3 Front panel Digital to Analogue Converter DAC-3MK 1 2 3 4 1 Power Button: Press this button, this unit will be switched on. Press it again, the power supply will be cut off. 2 Power Indicator: This indicator will be light when this unit is switched on. 3 Sampling Frequency indicator: The 96KHz indicator will be light while working. 4 Digital Signal locked indicator: This indicator will be light when the steady digital signal are received. 4 XA6950 Chapter 3 3. 4 Rear Panel Introduction 1 2 3 4 5 6 7 8 1 Right Balanced Audio Output Terminal Output the balanced audio signal (analog stereo)amplified by transistor to the input port on the amplifier. 2 Audio Output Terminal Output the analog stereo audio signal amplified by tube to the input port on the amplifier. 3 Audio Output Terminal Output the analog stereo audio signal amplified by transistor to the input port on the amplifier. 4 Left Balanced Audio Output Terminal Output the balanced audio signal (analog stereo)amplified by transistor to the input port on the amplifier 5 Digital Optical Input Terminal It is used to input the digital audio signal. You could input the digital audio signal of the CD, VCD, DVD or the computer to this unit by Optics cable. 6 Input Selection switch Select the optical and coaxial digital signal input. 7 Digital Coaxial Input Terminal It is used to input the digital audio signal. [. . . ] We use the advanced CAD technology, Two-sided hole-drilled glass and fiber plate which has excellent high-frequency characteristics and many grounding wires for shielding to reduce various disturbances and improve the Signal to Noise Ratio. 3 XA6950 Chapter 3 3. 2 Block Diagram Introduction U11 DIGITAL TO ANALOG CONVERTER 3. 3 Front panel Digital to Analogue Converter DAC-3MK 1 2 3 4 1 Power Button: Press this button, this unit will be switched on. Press it again, the power supply will be cut off. 2 Power Indicator: This indicator will be light when this unit is switched on. 3 Sampling Frequency indicator: The 96KHz indicator will be light while working. 4 Digital Signal locked indicator: This indicator will be light when the steady digital signal are received. 4 XA6950 Chapter 3 3. 4 Rear Panel Introduction 1 2 3 4 5 6 7 8 1 Right Balanced Audio Output Terminal Output the balanced audio signal (analog stereo)amplified by transistor to the input port on the amplifier. 2 Audio Output Terminal Output the analog stereo audio signal amplified by tube to the input port on the amplifier. 3 Audio Output Terminal Output the analog stereo audio signal amplified by transistor to the input port on the amplifier. 4 Left Balanced Audio Output Terminal Output the balanced audio signal (analog stereo)amplified by transistor to the input port on the amplifier 5 Digital Optical Input Terminal It is used to input the digital audio signal. You could input the digital audio signal of the CD, VCD, DVD or the computer to this unit by Optics cable. 6 Input Selection switch Select the optical and coaxial digital signal input. 7 Digital Coaxial Input Terminal It is used to input the digital audio signal. [. . . ]