User manual XTANT 2200IX

[. . . ] We all became excited about the possibilities. We Listen to your recommendations, opinions, and needs . We Listen to our fellow supporting manufacturers to ensure that our products interface well with a wide variety of products. We Listen to our equipment with sensitive and critical ears to provide the finest mobile audio components on the planet. [. . . ] Features include adjustable threshold and bypass switch. Balanced / Floating Input: All "ix" Series amplifiers are supplied with Balanced / Floating inputs. This circuitry helps to eliminate "system noise" associated with "ground-loops". Modular Expansion Port: Xtant amplifiers are supplied with a modular port used for docking any of Xtant's signal processing modules. Protection Circuitry: Both Thermal and Overcurrent protection has been incorporated into all Xtant amplifiers. In the event of a problem, the amplifier will reduce its power to maintain operation. Status LEDs: Four LEDs, visible through the cover, indicate operational status of all Xtant amplifiers. The red LED illuminates when the amplifier is "ON", the green LED indicates when the noise gate is open, the yellow LED indicates that overcurrent protection is employed and the orange LED indicates that the thermal protection circuit is operational. 5 Xtant 2200ix SPECIFICATIONS Frequency Response Number of Channels Watts per Channel @ 4 Watts per Channel @ 2 Bridged Mono @ 4 Recommended Load () Distortion (THD) MEASURED: 5 Hz to 50 kHz +/­ 1 dB 2 2 x 100 2 x 200 1 x 400 2 Stereo / > 4 Bridged < . 04% 20 HZ TO 20 KHZ AT RATED POWER, ALL CHANNELS DRIVEN 4 Signal to Noise Ratio > 100 dB MEASURED: A-WEIGHTED IN 20 KHZ NOISE BANDWIDTH @ 1 VOLT SENSITIVITY Damping Factor Input Sensitivity > 200 @ 100 Hz with 4 load 100 mV to 8. 5 V RMS Unbalanced Source 100 mV to 17 V RMS Balanced Source Input to Line Output Gain 0 dB +/­ 20 dB, Selectable in 10 dB steps On-Board Crossover Module Port(s) Power Supply Operational Voltage Fusing Warranty S E E PA G E 18 dB per Octave "Butterworth" 1 - Accessory Port Fully Regulated, "Transitional" 11 to 15 Volts 50 Amp Limited 4 year Parts and Labor 11 O F T H I S M A N U A L F O R C O M P L E T E D E TA I L S 6 ON-BOARD ELECTRONIC CROSSOVER The 22001X features a three-way electronic crossover. The crossover is tied to a set of inputs and controls the frequency range of the associated Channels. Independent frequency selection is provided for both the High and Low Pass sections. A set of selectable RCA line outputs (to feed additional components) are included with the crossover. In addition, the crossover features two on-board header jumpers (one for the amplifier and one for the RCA line outputs) which allows you to select Bypass (Full Range), High Pass, Low Pass, and/or Band Pass mode. When chosen, the Band Pass selection is available via the Low Pass jumper position for the RCA line outputs. The following Frequency Modules (SIPs)* are available from your Xtant Dealer: 50 Hz, 70 Hz, 80 Hz, 90 Hz, 120 Hz, 150 Hz, 300 Hz, 500 Hz, 700 Hz, 1 kHz, 3 kHz, 4 kHz, and 5 kHz. Please refer to the Installer's Reference (insert) for the Frequency Module receptacle(s) location and chart of frequency/SIP value code numbers * SIP: an acronym referring to multiple resistors in a Single In-Line Package 7 OPTIONAL ACCESSORY MODULES Xtant optional accessory modules are easily and quickly installable by your Authorized Xtant Dealer. The upgrade modules snap into place on the amplifiers PC board when the top of the unit is removed. These accessories enhance your entire system, expanding and customizing performance for your unique applications. PARAMETRIC EQUALIZATION MODULE ­ PQM 1 The PQM-1 is a precision tuning instrument, designed to be adjusted with the use of a Real-Time-Analyzer. This true, fully adjustable, one band parametric equalizer provides individual frequency, Q/bandwidth, and +/- 18dB gain adjustment controls. By utilizing one of three (3) frequency modules included, any frequency from 20 Hz to 20kHz can be chosen. The "Q" ranges from 1 to 10 in value, allowing a wide variety of bandwidth adjustment to address the subtle tuning requirements common to mobile audio systems. All 2-channel Xtant amplifiers can accept one PQM-1. All 3/4-channel amplifiers will accept two PQM-1 modules if desired (one PQM-1 per 2 channels of input). 24 DB / OCTAVE CROSSOVER MODULE ­ CM 24X The CM 24X upgrades the standard on-board crossovers provided on all Xtant "ix" and "x" Series amplifiers with a 24 dB per octave "Linkwitz - Riley" filter. [. . . ] ELECTRONICS X t a n t Te c h n o l o g i e s 7676 South 46th Street Phoenix, Arizona 85040 888-449-8268 SPEAKERS X t a n t Te c h n o l o g i e s 805 Woodman Ave. Winslow, Il 61089 800-556-2888 TO RETURN XTANT PRODUCTS OUT OF WARRANTY: Contact Xtant's Warranty Department at (602) 431 8686 from 8:00 am to 5:00 pm (MST) for a Return Authorization Number. Return the unit, postage prepaid, in the original protective carton. Please include a description of the problem and, if desired, a request for an estimate of repair costs. [. . . ]