User manual XTANT X215 TECHNICAL DATA REPORT

[. . . ] Adjustment is made by installing a jumper across the associated input voltage/pin location. Refer to the illustration on the reverse side of this document prior to setting the input sensitivity. INSTALLER DA T E INSTALLED: N A M E: ' S REFERENCE LOG xtant technologies installer's reference OWNERS PHONE: TH I S A D D R E S S: CI T Y/ ST A T E: V E H I C L E: XT A N T A M P L I F I E R: M O D E L CROSSOVER MODES OF OPERATION The 2200ix is equiped with two (2) crossover mode jumpers. The four (4) position header jumper controls the crossover function as it applies to the 2200ix's amplifier. [. . . ] The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, Position 3 = Low Pass, and Position 4 = Band Pass. (See illustration) The three (3) position jumper controls the crossover function as it applies to the RCA Line Outputs. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, and Position 3 = Low Pass. (See illustration ) The High and Low Pass frequenies are determined by the F r e q u e n c y M o d u l e s ( S I P s ) i n s t a l l e d i n t h e t w o ( 2 ) S I P s o c kets pictured on the reverse side of this document. ZI P: YE A R: S E R I A L# DOCUMENT H A S B E E N C R A F T E D T O M A K E I N S T A L L AT I O N, SYSTEM D E S I G N A N D TROUBLE- SHOOTING, A Q U I C K A N D E A S Y PROCESS. TH E C H A R T S P R O V I D E D, O F F E R A S I MP L E METHOD O F D O C U M E N T A T I O N. CROSSOVER SETTINGS: S I P HIGH P A S S V A L U E C O D E: S I P LOW P A S S V A L U E C O D E: I N P U T S E N S I T I V I T Y J U M P E R (CIRCLE SETTING) JUMPER SETTINGS: AMPLIFIER: (CIRCLE SETTING) IT IS IMPORTANT THAT YOU RETAIN THIS LOG FOR YOUR RECORDS. ON P A G E 1 2 O F T H E OWNER'S MA N U A L, Y O U W I L L F I N D T H E OWNER'S REFERENCE LOG. ONCE Y O U H A V E N O T A T E D T H E F I N A L SETTINGS F O R T H I S 2 2 0 0I X, T R A N S F E R THOSE SETTINGS T O T H E OWNER'S REFERENCE LOG. IN T H E F U T U R E, A N Y SYSTEM E X P A N S I O N A N D/ O R PROBLEMS M A Y B E REFERENCED T O T H I S LOG. A L L HIGH LOW B A N D P A S S INSTALLATION SEQUENCE R C A O U T P U T S (CIRCLE SETTING) ALL HIGH LOW REMOVE AMPLIFIER COVER: Loosen allen head screws and lift-off cover. i. e:. Speaker, Power, Remote, Ground, and RCA i n p u t . DOUBLE CHECK ALL CONNECTIONS!TURN ON AMPLIFIER. Check red LED, it should be on. ADJUST LEFT, RIGHT AMPLIFIER GAINS. ADJUST NOISE GATE THRESHOLD (IF USED): SPECIAL COMPONENTS SERIAL SERIAL Turn noise gate on and adjust the threshold by turning clockwise to increase sensitivity (gate will open with less i n p u t s i g n a l ) . T h e g r e e n LED w i l l i l l u m i n a t e w h e n t h e gate passes signal. AFTER FINE TUNING THE SYSTEM: xtant technologies · · · · · · · · · 7 6 7 6 SOUTH 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602. 431. 8686 Remove protective covering from amplifier and clean per the maintanence section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base. · · · · · · · · · INSTALLER'S . REFERENCE. . . . . . . . . . . . . INDEPENDENT LEFT AND RIGHT AMPLIFIER GAIN FREQUENCY SELECTION: CROSSOVER CONTROLS ­ ROTATE CLOCKWISE TO INCREASE SENSITIVITY. TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REMOVE AND REPLACE THE FREQUENCY MODULE (SIP) LOCATED ON THE CIRCUIT BOARD NEXT TO THE CROSSOVER MODE JUMPERS. NOTE THAT THE IDENTITY OF THE HIGH & LOW P ASS SOCKETS ARE NOT MARKED ON THE BOARD. [. . . ] . . . . . . . . . . . . INDEPENDENT LEFT AND RIGHT AMPLIFIER GAIN FREQUENCY SELECTION: CROSSOVER CONTROLS ­ ROTATE CLOCKWISE TO INCREASE SENSITIVITY. TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REMOVE AND REPLACE THE FREQUENCY MODULE (SIP) LOCATED ON THE CIRCUIT BOARD NEXT TO THE CROSSOVER MODE JUMPERS. NOTE THAT THE IDENTITY OF THE HIGH & LOW P ASS SOCKETS ARE NOT MARKED ON THE BOARD. REFER TO THIS DRAWING FOR LOCATION & THE CHART ON THE BACK FOR THE AVAILABLE SELECTION OF SIP / FREQUENCY VALUES. right Left HIGH PASS SIP INPUT SENSITIVITY: TO ADJUST INPUT GAIN, MOVE JUMPER (IF NEEDED) ­ AND INSTALL IT IN THE LOCATION WHICH MATCHES YOUR INPUT SIGNAL LEVEL. [. . . ]