User manual YAESU FT DX 9000 TFT

[. . . ] FTDX9000 TFT OPERATION MANUAL FTDX9000 TFT OPERATION MANUAL PLEASE READ THIS FIRST When turning on the transceiver for the first time, please set the local time as soon as possible. If this is not done, the various functions of the World Clock and Great Circle Map will not function correctly. Note: If you wish to add a city to the City List that was programmed at the factory, you will need to supply your own USB or PS2 Keyboard. If you utilize one of the pre-loaded cities, a keyboard is not necessary. [. . . ] While using LBWS, it is not possible to switch to the dual display mode. Note:The QMB marker will not appear on the screen while LBWS is engaged. "LBWS" Select "LBWS" Select Page 16 FTDX9000 TFT OPERATION MANUAL SPECTRUM SCOPE USING THE FIX (FIXED) MODE This feature is convenient when you want to monitor an entire amateur band. The starting point, located at the left edge of the screen, can be set via the Menu. Even if the screen span (bandwidth) is changed, the start frequency will not be changed. By watching the screen, you can move your operation to frequencies where interesting activity appears on the display. Just as with the CTR mode, it is possible to toggle the Main (VFO-A) or Sub (VFO-B) VFOs. It is also possible to utilize a dual display, with the Main (VFO-A) VFO in the upper position, and the Sub (VFO-B) VFO below. By pressing the [F7](CTR/FIX) key, it is possible to switch between the CTR mode and the FIX mode. Press the [F2](SPAN) key to set the desired value for the Span (bandwidth). By pressing the [F2](SPAN) key, the span will change as follows. 25 kHz 50 kHz 100 kHz 250 kHz 500 kHz 1000 kHz 2500 kHz 25 kHz . . . . . . Press the [F3](ATT) key to set the desired attenuation value. By pressing the [F3](ATT) key, the attenuation will change as follows. Press the [F4](A/B) key to toggle between the Main (VFO-A) and Sub (VFO-B) VFOs. Press the [F5](DUAL) key to engage dual spectral display. The Main VFO will appear in the upper display field, and the Sub VFO will appear in the lower. If the receive frequency is outside of the screen, the position of the operating frequency will be "shown" in the lower area of the display as "<<" ">>", and "RCV Freq is out of range will also be range" RCV displayed. You may clear the "Average indication" or "Peak indication" which was set by TRACE MODE (See page 15) by pressing the [F7](REFRESH) key. Just as in the CTR mode, you can use the Marker. Please see page 14 for information on using the marker. "SPAN" Select "ATT" Select "REFRESH" "CTR/FIX" Select SETTING THE LEFT EDGE FREQUENCY FOR THE FIX MODE Press the [MNU] key momentarily to enter the Menu mode. Select the item which you want to change by rotating the Main dial (in this case, the items will be in the range from "SCOPE 112 MAIN FIX 1. 8 MHz" to "SCOPE 133 SUB FIX 50MHz"). Now you may change the setting by rotating the Sub dial. [. . . ] Use the Main Tuning Dial, or the the [F6]( )/ [F7]( ) keys, to select the Menu item you wish to work on. Use the CLAR/VFO-B knob, or the [F4]( )/[5]( ) keys, to change the setting of the selected Menu item. Press the [MNU] key is pressed for 2 seconds to save (within the transceiver) the new setting; the menu screen will close, and you will then return to the screen that was in use before entering the menu mode. If you press the [MNU] key momentarily to exit, the new settings will not be saved, and you will exit from the menu mode without retaining the new configuration. MENU MODE RESET 1. [. . . ]