User manual YAESU FT-301

[. . . ] DMU Band scope Display Signal Peak Frequency is centered. Ver. 11. 54 EDSP implements improvements (also includes all previous updates): · Corrected FM TX for a slight frequency offset. NOTES: *Rotate the [METER] switch to select "COM" (Compression). We recommend setting the PROC level within the 5dB to 10dB range. *When menu settings are saved on the DMU-2000 CF card and transferred to the new version, some previous versions may not transfer correctly. [. . . ] Plug the mini-DIN connector of the CT-119 into the PGM jack. Be sure that the arrow indicator on the mini-DIN plug is down. Plug the AC cord into the radio and turn the main power switch on the back of the radio to the ON position. [NOTE: The radio will not show a display now. ] Main Power SW PGM (6) Click on [WRITE] in the program window. A status bar with green bars should appear below the [WRITE] button. Note disregard the on screen instruction to [3. Turn "S3004" on]. When the loading process is complete, an [OK?] box will appear. Turn off the main power switch, (or turn off the power supply for FT-301 and wait a minute, until the capacitors discharge) and unplug the AC power cord. (10) Plug the AC power cord into the radio and turn the main power switch on the back of the radio to the ON position (or turn on the power supply for FT-301). Press and hold in the [FAST] and [LOCK] keys; while holding them in, press the front power switch to turn the radio on. This resets the radio and locks in the new software. Turn the front Power Switch and the Main Power Switch in the back OFF (or turn off the power supply for FT-301 and wait a minute, until the capacitors discharge) and remove the AC power cord. This resets the radio and locks in the new software. Press and hold in the [FAST] and [LOCK] keys; while holding them in, turn the radio back on (this resets the radio and locks in the new software). NOTE: We recommend trying the new factory default settings rather than transferring your old ones, because of the changes in the EDSP and the Main CPU, you may wish to make new settings. We hope this new software will increase your enjoyment of your FT-2000/D. If you have any problems or questions please contact Vertex Standard, Amateur Tech Support. amateurtech@vxstdusa. com Best regards, Mikio Maruya, WA6F Executive Vice President Engineering & Customer Service Vertex Standard USA, Inc. Vertex Standard USA, Inc. | Cypress, CA 90630 | 714. 827-7600 | FAX: 714. 827-8100 www. vertexstandard. com ADDENDUM If the CT-119 programming cable or 8-pin mini-DIN PGM-SW (P0091526) is not available you will need a serial cable RS-232C, DB9F to DB9F straight cable. MAIN Software Update *Don't forget to write down (or save to a CF Card) any personal menu settings you have changed from the default before you start. Please see the DMU-2000 Data Management Operation Manual for the procedure to save your settings to a CF card. We recommend you follow this process, steps (1) thru (18), the first time you program your radio. After you are familiar with the location of the switch S3004 you may wish to bypass Steps (2) and (15), and operate the switch through the hole under the left rear foot (near the CAT connector). You must be extremely careful to avoid damage to the PC components (which may not be covered by the Limited Warranty). Use a flashlight and insulated tool to operate the switch. [. . . ] Do not interrupt the process until it completes. When the loading process is complete, an [OK?] box will appear. (Located on the rear panel of the FT-2000 or on the front of the power supply for the FT-301. ) Disconnect the AC power cord (or turn off the power supply for FT-301 and wait a minute, until the capacitors discharge). Switch the programming micro switch S3004 to the off position. [. . . ]