User manual YAESU FTM-350

[. . . ] DUAL BAND FM TRANSCEIVER FTM-350 SERIES OPERATING MANUAL VERTEX STANDARD CO. , LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A. YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. VERTEX STANDARD HK LTD. Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong VERTEX STANDARD (AUSTRALIA) PTY. , LTD. Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Australia Contents Front Panel Controls & Switches . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Timer Page Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Radio Page Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 [SMART FUNCTION] Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the microphone PTT switch to begin transmission. While transmitting, press the desired number keys on the microphone. When you have sent all the digits desired, release the PTT switch. DTMF AUTODIALER 1. To store a telephone number to a DTMF memory register, press the [SET] key and choose the "SIGNALING" group, then choose item "J02 DTMF MEMORY". Choose a DTMF register and enter the telephone number. Then Set Mode item "J03 DTMF MODE" in the "SIGNALING" group to "ON". Press the [ESC] key three times, to exit from the Set Mode, and activate the DTMF Autodialer. To send the telephone number, perform the following procedure while pressing the PTT switch: 1) Press the [DTMF] key (located at the left side of the [POWER] key while transmitting). 2) Rotate the [DIAL] knob to select the DTMF memory register corresponding to the telephone number you wish to send. 3) Press the [DTMF] key again to transmit the telephone number. To disable the DTMF Autodialer, select the "OFF" selection in the Set Mode item "J06 DTMF MODE". You may send a telephone number by pressing the microphone numeric keys ([1] through [9]) corresponding to the DTMF memory string you wish to send. 22 FTM-350 SERIES OPERATING MANUAL BARO/ALTI PAGE OPERATION The FTM-350 Series Transceiver can display the current Barometric Pressure and relative changes in the pressure. Furthermore, when an optional FGPS-1 or FGPS-2 GPS Unit is installed, the FTM-350 Series Transceiver can display the current altitude and relative changes in the altitude. First, enable the "BARO/ALTI" page, by pressing the [SET] key and choosing the "DISPLAY" group. Then select the Set Mode item "C01 DISPLAY SELECT" and set the "BARO/ ALTI" page to ON. Press the [ESC] key three times to exit the Set Mode. To display the "Baro/Alti" Page, enable the "BARO/ALTI" page via Set Mode item "C01 DISPLAY SELECT" in the group, beforehand. See page 37. 1 1 Press the [FWD] or [BCK] key repeatedly, until the "BARO/ALTI" Page appears. The current Barometric Pressure appears at the upper right of the display. A chart that indicates the relative changes in the pressure (barometric chart) is presented in the left half of the display. Additionally, if you install the optional GPS Unit, your current altitude appears at the upper right of the display, and your current position (Longitude/ Latitude) appears at the lower right of the display. Press the [SCALE] key to change the time scale of the barometric chart. Available selections are "2H", "6H", "12H", and "24H". [. . . ] 10 GPS DATUM: Select the GPS datum to be used. 11 XBAND REPEATER: Activates Cross Band Repeater operation. Set the right band to a 144 MHz frequency and the left band to a 430MHz frequency (or vice versa) before beginning this procedure. Once you have made your selection in step 3, press the left side [DIAL] knob and confirm that (OK? [. . . ]