User manual YAKUMO TFT 15 AL

[. . . ] 4 4. 6 OSD menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. 7 Self test pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 8 Safety protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 9 Preset modes timing chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the power cord or plug is damaged or frayed. If liquid has been spilled into the monitor. If the monitor has been exposed to rain or water. If the monitor has been dropped or the cabinet has been damaged. When the monitor exhibits a distinct change in performance this indicated a need for service. Introduction Chapter 1 Introduction 1. 1 Features Multi-scanning at horizontal frequencies of 30~60KHz(15"), 30~80KHz(17") and vertical frequencies of 60Hz to 75Hz. Microprocessor based with OSD (On Screen Display) control. Compatible with standard IBM VGA, extended VGA, super VGA, IBM XGA modes, as well as VESA resolution standards. Microsoft Windows 9x/2000/XP compatible & VESA Display Data Channel (DDC) 1/2B compatible. 1. 2 Checking List Please make sure the following items are included with your LCD monitor. Your monitor AC Adapter AC power cord VGA Signal cable Audio cable If any of these items are missing, please contact with your dealer for technical support and custom service. Note: Be sure to save original box and all packing material for transport in future if the monitor need, 1 Chapter 2 Installation 2. 1 Connect your monitor to computer 1 Turn off your computer and unplug its power cable. Installation 2 Connect the power cable for your monitor to the DC adapter and connect the adapter the DC power jack on the back of your monitor. 3 Connect the PC AUDIO IN jack to audio in for PC. 4 Connect the DVI or D-Sub 15Pin signal cable to the video port on the back of your computer 5 Plug the computer and monitor power cables into a nearby outlet. 6 Turn your computer and monitor on, if your monitor display an image, you have successfully installed the monitor. If the monitor does not display an image, check all the connections. 1 2 3 Connecting the monitor to the computer and the power supply 2 Over view of your monitor Chapter 3 Over view of your monitor 1 2 2 3 4 5 3. 1 Front panel over view MENU DO WN UP AUTO POWER 1. Auto Button (AUTO) 3. 2 Rear panel over view 1 2 3 1. DVI/VGA IN 3 Chapter 4 4. 1 Power ON/OFF Switch OPERATION Direct ­ Access Features OPERATION Direct ­ Access Features This button is used to turn the monitor on and off. NOTE : The ON/OFF switch does not disconnect the device from the main voltage. To completely disconnect the mains voltage, please remove the power plug from the socket. 4. 2 Power indicator This indicator lights up blue/green when the monitor operates normally. If the monitor is in power saving mode, this indicator change to amber when monitor is turn off, this indicator change to dark. 4. 3 Auto Auto adjust function : Press AUTO button and release, the auto adjust display mode will tune to the utmost performance according to VGA setting. , Change mode Function : Press AUTO button 2 seconds and release to enter signal search mode. , You could choose among signals by pressing and release AUTO button. 4. 4 Volume This feature adjust the DOWN button to decrease the volume and adjust UP button to increase the volume. 4. 5 Menu Features The following features can all be accessed using your monitor on screen menu system. Making adjustments to a feature, pushing the exit button to turn off the menu. Please follow the procedure of selection and adjust an item using the OSD system as below steps for main functions adjustment. Press MENU Button to activate the OSD menu. Step 2. Press Select Button DOWN or Select Button UP to scroll the highlight through the main function list. [. . . ] language You can choose one of the nine languages you need. exit To exit the main menu. utilities 1. osd timeout You can select how long the monitor waits after the last adjust of the key to shut off the OSD menu. The time setting choices are from 5 to 60 seconds. [. . . ]