User manual YAMAHA 01XE3

[. . . ] Quick Reference Direct Recording Recording to Computer/Audio Sequencer (DAW) Recording a Mix 6 Set up the computer (with mLAN connection) and audio sequencer for recording. 1. Using the mLAN Auto Connector, make sure the number of channels (in "From 01X to PC/Mac") is equal to or higher than the number of channels to be recorded. Select the input channels of the mLAN Audio Driver on the sequencer. [. . . ] 1: Use the Stereo Bus for monitoring the overall sound, and record specific channels via the Rec Bus. 1. Set Rec Bus to ON for the channel(s) you wish to record via Rec Bus. 90) OUT PATCH (mLAN Out Channel): RECBUS = [1/2] Effects can also be inserted in the signal path of each channel. Effect 1/2 PATCH = channel number (p. Dist. ) Effect 1 (Reverb) 01X STI1 Fader 5 Adjust the output level with 3 Apply effects, such as reverb, for monitoring purposes by adjusting the levels of Aux Send 3 (or 4) in the individual channels and STI 1 (or 2) in the Master layer (with faders). (The effect is not recorded; only the dry signal is. ) 4 Adjust the direct monitor level for each channel to be recorded with the individual channel faders. You can also record the mLAN output, This allows you to monitor adjusting the output level with the fader. 91) without latency (delay). DIRECT OUT POSITION = POST FADER the STEREO fader and the MONITOR/PHONES knob. Ex. 2: For vocal recording, monitor the overall sound via the Stereo Bus and set up a separate monitor mix for the vocalist (with STEREO/AUX OUT), recording the microphone signal directly. 1. Set the Rec Bus output to ON for only those instrument channels you want in the monitor mix for the vocalist. OUT PATCH (St/Aux Out Port) : RECBUS = ST/AUX OUT (p. Apply reverb or other processing to the monitor mix as desired. Set the Rec Bus of the STI 1 (in the Master layer) to ON. (See "Direct Recording" above. ) * In these explanations, normal page references are to the 01X Owner's Manual; those indicated by "Guide" are to the 01X Installation Guide. For more information, make sure to refer to the "Overview of the 01X" on page 25 of the Owner's Manual, as well as the block diagram at the end of the manual. Quick Reference Stereo Playback (two-channel mix) Audio Playback from the Computer/Sequencer (DAW) Playback of Individual Channels In this setup, each audio channel on the software mixer (DAW) is sent to the corresponding channel of the 01X. Audio Sequencer Software Audio Mixer Computer This setup lets you play back the main stereo output from the software mixer (DAW) from the 01X. Audio Sequencer Software Audio Mixer Computer 1 Send the main stereo output of the sequencer to channels 1 and 2 of the mLAN Audio Driver. 70. ) 2 Use the mLAN Stereo Inputs (Monitor In) for the sequencer's stereo output. · By connecting the stereo output of the sequencer to the mLAN Stereo Inputs, you can monitor the both the sequencer output and the 01X output, without having to use 01X input channels for monitoring. · The available channels of the mLAN Audio Driver depend on the settings of the mLAN Auto Connector. [. . . ] mLAN Audio Driver Ch. 1, 2 OUT PATCH [ST-BUS] = D. OUT <P. 91> Effect 1, 2 SEND3, 4 STI1, 2 Fader Effect 1, 2 SEND3, 4 EQ, Dyn, Vol EQ, Dyn, Vol MIDI Pan STI1, 2 Recorder (Digital connection) Mix 1 Assign the audio channels on the sequencer to the channels of the mLAN Audio Driver, from The actual output settings differ depending on the sequencer (DAW). 70) For example: · Each mixer channel on the sequencer is assignable to one of the mLAN channels. · Each mixer channel on the sequencer is assigned to a bus, and the bus is assignable to one of the mLAN channels. Mic / Guitar Synthesizer EQ, Dyn, Vol EQ, Dyn, Vol Monitor WC96730 311POCP38. 2-01A0 Printed in Japan [. . . ]