User manual YAMAHA 25HP-2000

[. . . ] In this Owner's Manual particularly important information is distinguished in the following ways. cC A CAUTION indicates special precautions that must be taken to avoid damage to the outboard motor. NOTE: A NOTE provides key information to make procedures easier or clearer. * Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your machine and this manual. [. . . ] For setting the outboard motor at the partially tilted position, slightly tilt up the engine until the plate turns completely To return the engine to the normal position, put the engine in Neutral, then slightly tilt up the engine. Set the tilt-lock lever and shallow water lever to the lock position and slowly tilt the engine down. 402072* 25-3/30 3) 412022 3-26 E EMH10110 TILTING UP/DOWN If the engine will be stopped for some time, or if the boat is moored in shallows, the engine should be tilted up to protect the propeller and casing from damage by collision with obstructions, and also to reduce salt corrosion. 105031 cC 8 Before tilting the motor, follow the procedures under "STOPPING ENGINE". Never tilt the motor while the engine is running. Severe damage from overheating can result. 8 Do not tilt up the engine by pushing the steering handle as this could break the handle. 8 Keep the power unit higher than the propeller at all times. Otherwise, water can run into the cylinder, causing damage. w Be sure all people are clear of the outboard motor when adjusting the tilt angle, also be careful not to pinch any body parts between the drive unit and engine bracket. w Leaking fuel is a fire hazard. Disconnect the fuel line if the engine will be tilted for more than a few minutes. (If the fuel connector is provided on the motor. ) 3-27 E EMG63910 N PROCEDURE FOR TILTING UP 25 1) 2) Place the gear shift lever in Neutral. Remove the fuel line connection from the motor. 406012 3) Push the tilt lock lever to release. 402061** 4) Pull up the shallow water lever. 402075* 5) 6) Hold the rear of the top cowling with one hand and fully tilt the engine up. The tilt support bar turns to the locked position automatically. 3-28 E EMG63010* PROCEDURE FOR TILTING UP 25-3/30 1) Remove the fuel-line connection from the motor. 8 Store the outboard motor in a dry, well-ventilated place, not in direct sunlight. 4-4 E EMU01796 STORING OUTBOARD MOTOR 30 When storing your Yamaha outboard motor for prolonged periods of time (2 months or longer), several important procedures must be performed to prevent excessive damage. This is especially important for your oil injection-equipped outboard motor due to the lean oil ratios used at idle prior to shutting the engine off for the season. It is advisable to have your outboard motor serviced by an authorized Yamaha dealer prior to storage. However, the following procedures can be performed by you, the owner, with a minimum of tools. EMK21010 Filling Fuel Tank Fill the fuel tank with fresh fuel and add one ounce of "Yamaha Fuel Conditioner and Stabilizer" (Part No. NOTE: The use of "Yamaha Fuel Conditioner and Stabilizer" eliminates the need to drain the fuel system. Consult your Yamaha dealer or other qualified mechanic if the fuel system is to be drained instead. 4-5 E EMK22211 q w Flushing Cooling System and Fogging Engine Cooling system flushing is essential to prevent the cooling system from clogging up with salt, sand, or dirt. In addition, fogging of the engine is mandatory to prevent expensive engine damage due to rust. Perform the flushing and fogging at the same time. 2) Install the outboard motor on the water tank, and fill the tank with fresh water to above the level of the anticavitation plate. 1 Water surface 2 Lowest water level 605024 cC If the fresh water level is below the level of the anti-cavitation plate, or if the water supply is insufficient, engine seizure may occur. w 8 Do not touch or remove electrical parts when starting or during operation. 8 Keep hands, hair and clothes away from flywheel and other rotating parts while engine is running. 3) 4) Run the engine at a fast idle for 10~15 minutes. [. . . ] If a question or problem arises regarding warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. If you are still not satisfied and require additional assistance, please write: YAMAHA MOTOR CORPORATION U. S. A. CUSTOMER RELATIONS DEPARTMENT P. O. Box 6555 Cypress, California 90630 When contacting Yamaha Motor Corporation, U. S. A. [. . . ]