User manual YAMAHA 9.9HP-2000

[. . . ] In this Owner's Manual particularly important information is distinguished in the following ways. cC A CAUTION indicates special precautions that must be taken to avoid damage to the outboard motor. NOTE: A NOTE provides key information to make procedures easier or clearer. * Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your machine and this manual. [. . . ] Slightly tilt up the engine until the tilt support bar is released automatically. Tilt down the engine. 3-23 E EMH60010 CRUISING IN OTHER CONDITIONS CRUISING IN SALT WATER After operating in salt water, wash out the cooling-water passages with fresh water to prevent them from becoming cloggedup with salt deposits. NOTE: Refer to cooling system flushing instructions in "TRANSPORTING AND STORING OUTBOARD MOTOR". CRUISING IN TURBID WATER It is strongly recommended that the optional chromium-plated water-pump kit be installed if the outboard is to be used in turbid (muddy) water conditions. 3-24 E -MEMO- E EMK00010 Chapter 4 MAINTENANCE 1 2 3 4 5 6 SPECIFICATION DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 TRANSPORTING AND STORING OUTBOARD MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Trailering outboard motor. . . . . . . . . . . . . . . . . . . 4-3 Storing outboard motor . . . . . . . . . . . . . . . . . . . . . . 4-4 PERIODIC MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . 4-7 Replacement parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Maintenance chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Cleaning and adjusting spark plug. . . . . 4-9 Checking fuel system. . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Inspecting fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Adjusting idling speed. . . . . . . . . . . . . . . . . . . . . . . 4-13 Checking wiring and connectors . . . . . . 4-14 Exhaust leakage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Water leakage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Greasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Checking propeller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Changing gear oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Cleaning fuel tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Inspecting and replacing anode . . . . . . . 4-20 Checking bolts and nuts . . . . . . . . . . . . . . . . . . . . 4-21 Motor exterior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Coating the boat bottom . . . . . . . . . . . . . . . . . . . 4-21 E EMR50302* SPECIFICATION DATA Model Item DIMENSIONS 8Overall Length 8Overall Height 8Overall Width 8Transom height 8Weight PERFORMANCE 8Full throttle operating range 8Maximum output 8Idling speed (in neutral) ENGINE 8Engine type Displacement Bore × stroke 8Ignition system 8Spark plug Spark plug gap 8Control system 8Starting system 8Alternator output 8Starting carburetion system DRIVE UNIT 8Gear positions Gear ratio 8Trim/tilt system 8Propeller mark FUEL AND OIL 8Fuel Fuel tank capacity 8Recommended engine oil Lubrication Fuel:oil ratio 8Recommended gear oil Gear oil quantity TIGHTENING TORQUE 8Spark plug 8Propeller nut N·m (kgf·m, lb·ft) N·m (kgf·m, lb·ft) 25 (2. 5, 18) 17 (1. 7, 12) L (US gal, Imp gal) Regular unleaded gasoline (P. O. N. : minimum 86) 25 (6. 6, 5. 5) YAMALUBE, 2 STROKE OUTBOARD OIL or an equivalent TC-W3 certified outboard oil Premix 100 : 1 Hypoid gear oil (SAE 90) 250 (8. 5, 8. 8) Forward-Neutral-Reverse 2. 08 (27/13) Manual J cm3 (cu. in. ) mm (in. ) NGK mm (in. ) 2-stroke, L2 246 (15. 01) 56 × 50 (2. 20 × 1. 97) C. D. I B7HS-10 0. 9~1. 0 (0. 035~0. 039) Tiller control Manual start 12-(80) Choke valve start system r/min kW (HP) r/min 4, 500~5, 500 7. 3 (9. 9) at 5, 000 r/min. 700~800 S S S mm (in. ) mm (in. ) mm (in. ) mm (in. ) kg (lb. ) 873 (34. 4) 1, 040 (40. 9) 332 (13. 1) 440 (17. 3) 36 (79) Unit 9. 9MSHB V-A (W) Fuel:Oil cm3 (US oz, Imp oz) 4-1 E 15MSHB -- -- 873 (34. 4) 1, 040 (40. 9) 332 (13. 1) 440 (17. 3) 36 (79) 4, 500~5, 500 11. 0 (15) at 5, 000 r/min. 700~800 2-stroke, L2 246 (15. 01) 56 × 50 (2. 20 × 1. 97) C. D. I B7HS-10 0. 9~1. 0 (0. 035~0. 039) Tiller control Manual start 12-(80) Choke valve start system Forward-Neutral-Reverse 2. 08 (27/13) Manual J Regular unleaded gasoline (P. O. N. : minimum 86) 25 (6. 6, 5. 5) YAMALUBE, 2 STROKE OUTBOARD OIL or an equivalent TC-W3 certified outboard oil Premix 100 : 1 Hypoid gear oil (SAE 90) 250 (8. 5, 8. 8) 25 (2. 5, 18) 17 (1. 7, 12) 4-2 E EMU01369 TRANSPORTING AND STORING OUTBOARD MOTOR w Leaking fuel is a fire hazard. When transporting and storing the outboard motor, close the air vent screw and fuel cock to prevent fuel from leaking. TRAILERING OUTBOARD MOTOR The motor should be trailered and stored in the normal running position. If there is insufficient road clearance in this position, then trailer the motor in the tilt position using a motor support device such as a transom saver bar. cC Do not use the tilt support lever/knob when trailering the boat. The outboard motor could shake loose from the tilt support and fall. If the motor can not be trailered in the down position, use an additional support device to secure it in the up position. w 8 Never get under the lower unit while it is tilted, even if a motor support bar is used. Severe injury could occur if the outboard accidentally falls. 8 USE CARE when transporting fuel tank, whether in a boat or car. Grease the spark plug threads and reinstall the spark plugs and torque to proper specification. (Refer to the Periodic Maintenance section, "Cleanning and adjusting spark plug. "). 2) Turn the engine over with the stop lanyard disconnected to work the fogging oil into the piston rings. (Refer to the Periodic Maintenance section, "Changing gear oil. "). Inspect the oil for the presence of water which indicates a leaky seal. Seal replacement should be performed by an authorized Yamaha dealership prior to use. (Refer to the Periodic Maintenance section, "Greasing. ") EMK27010 Cleaning and Anti-corrosion Measure 1) Wash down the exterior of the outboard with fresh water and dry off completely. 2) Spray the engine's exterior with Yamaha Silicone Protectant (Part No. 3) Wax the cowling with a non-abrasive wax such as Yamaha Silicone Wax (Part No. ACC-11000-15-02). 4-6 E EMU01569 PERIODIC MAINTENANCE w Be sure to turn off the engine when you perform maintenance unless otherwise specified. If the owner is not familiar with machine servicing, this work should be done by a Yamaha dealer or other qualified mechanic. [. . . ] This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U. S. A. by the selling dealer at the time of your purchase. If you should move after you have purchased your new outboard, please advise us of your new address by sending a postcard listing your outboard model name, engine serial number, dealer number (or dealer's name) as it is shown on your warranty identification, your name and new mailing address. Mail to: YAMAHA MOTOR CORPORATION, U. S. A. [. . . ]