User manual YAMAHA A-520

[. . . ] The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 10 Power Sources ­ The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection ­ Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. 12 Cleaning ­ The unit should be cleaned only as recommended by the manufacturer. 13 Nonuse Periods ­ The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. [. . . ] The sound is dense and highly concentrated. This program is ideally suited for rock music. You will experience a dynamic and lively sound field. BASIC OPERATION This program creates the expansive ambience of a large concert hall. It is suited for orchestra and opera music. CINEMA DSP: Dolby Surround + DSP/Dolby Digital + DSP s Dolby Pro Logic + 2 digital sound fields Digital sound fields are created in both the presence and rear surround zones of the Dolby Pro Logic-decoded sound field. They create a wide acoustic environment and emphasize the surround effect in the room, letting you feel as much presence as if you were watching a movie in a popular Dolby Stereo theater. ADVANCED OPERATION s Dolby Digital + 3 digital sound fields Digital sound fields are created in the presence zone and independently on the left and right surround zones of the Dolby Digital-decoded sound field. They create a wide acoustic environment and strong surround effect in the room without losing high channel separation. With the wide dynamic range of Dolby Digital sound, this sound field combination lets you feel as if you were watching a movie in the newest Dolby Digital theater. This is the most ideal home theater sound at the present time. APPENDIX English 25 TUNING Automatic tuning is effective when station signals are strong and there is no interference. However, if the signal from the station you want to select is weak, you must tune in to it manually (manual tuning). 5 1 Press PRESET/TUNING h once to tune in to a higher frequency and l once to tune in to a lower frequency. Press the button again if the tuning search does not stop at the desired station. Note ­ + ­ + L R · If you tune in manually to an FM station, it will be automatically received in monaural mode to increase the signal quality. y 5 42 3 · Use the manual tuning method if the tuning search does not stop at the desired station (because the signal from the station is weak). · When tuned in to a station, the frequency of the received station is shown on the display. Automatic Tuning 1 Use INPUT to select the tuner as the input source. Manual Tuning 1 Use INPUT to select the tuner as the input source. 2 Press FM/AM to select the reception band (FM or AM). The "MEMORY" indicator flashes for about five seconds. 1 2 Flashes 3 Press A/B/C/D/E repeatedly to select the desired group (A to E) of preset stations before the "MEMORY" indicator goes off. Make sure that " z " appears on the display. The selected group appears on the display. 1 2 1 Press A/B/C/D/E to select the required group of preset stations. Make sure that " z " appears on the display. or Front panel Remote control 4 Press PRESET/TUNING h or l to select a preset station number (1 to 8) with which you want to store the station before the "MEMORY" indicator goes off. Press h to select a higher preset station number and l to select a lower preset station number. Press MEMORY before the "MEMORY" indicator goes off. The displayed station has been stored as the preset group and number you have selected, and the reception band and frequency appear on the display. 2 5 Press PRESET/TUNING h or l (or PRESET +/­) to select a preset station number (1 to 8). The preset group and number appear on the display along with the reception band, frequency and signal strength information. or Front panel Remote control 6 Repeat steps 1 to 5 to store other stations. Notes · A new setting can be stored in place of the former one. · The reception mode (stereo or monaural) is stored along with the station frequency. 28 TUNING Exchanging Preset Stations You can exchange the assignment of two preset stations with each other. INTRODUCTION s Example: If you want to exchange preset station "E1" with "A5". 2, 4 PREPARATION ­ + ­ + L R 1 2 Recall preset station "E1". Refer to the procedure in the section "To Recall a Preset Station" on page 28. [. . . ] 31 Sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Speaker Output levels (TIME/LEVEL mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Output mode (SET MENU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32, 33 Speaker balance (test tone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]