User manual YAMAHA A-55N

[. . . ] Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] Select this setting when the surround speakers are small. Select this setting when you do not use the surround speakers. This unit is set to the Virtual CINEMA DSP mode (see page 50), and "Surround Back" is automatically set to "None". Bass Out (Bass out) Use this feature to select the speakers that output the LFE (low-frequency effect) and the low-frequency signals. LFE signals output Subwoofer and speakers Choice Subwoofer Both SWFR Front Output Output No output Front speakers Output No output Output Other speakers No output No output No output y See page 15 for the connection information of the surround speakers. 92 En Graphical user interface (GUI) screen Low-frequency signals output Subwoofer and speakers Choice Subwoofer Both SWFR Front *1 *4 No output Speaker Distance (Speaker distance) Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Thus, a certain amount of delay must be applied to the sound from each speaker so that all sounds will arrive at the listening position at the same time. Front speakers *2 *3 *1 Other speakers *3 *3 *3 *1 Output(s) the low-frequency signals of the front channels and other speakers set to "Small" or "None". *2 Always output the low-frequency signals of the front channels. *3 Output the low-frequency signals if the speakers are set to "Large". *4 Outputs the low-frequency signals of the speakers set to "Small" or "None". Test Tone Speaker Set Speaker Distance Speaker Level Subwoofer Unit Front L Front R Center Bass Cross Over (Bass cross over) Use this feature to select the crossover frequency of all the speakers set to "Small" or to "None" in "Speaker Set" (see pages 91 and 92). All frequencies below the selected frequency will be sent to the subwoofer or to the speakers set to "Large" in "Speaker Set" (see pages 91 and 92). To specify the other parameters, you need to first set "DHCP" to "Off". Shuffle (Shuffle) Use this feature to set this unit to play songs or albums in a random order. Choice Off On Functions Deactivates the shuffle function. " " appears in the top right corner of the playback status screen. 4 5 Press 4k / n to select the desired parameter and then 4h. Press 4l / h repeatedly to select the digit to change and then press 4k / n repeatedly to change the number. Press 4ENTER to confirm the setting of the parameter. Repeat steps 4 through 6 to configure each network parameter. Press 4n repeatedly to select "Setup" and then 4ENTER to finish configuration. Information (Network information) Use this feature to display the network system information. ADVANCED OPERATION 6 7 8 Network Play Style Information MAC Address 00:00:00:00:00:00 Status 100 BASE-TX Full Duplex System ABCDE123 Note The above display is an example. Note In case you have changed your network configuration, you may need to reconfigure the network settings again. y You can reset the network settings of this unit to the initial factory settings by using "NETWORK" of "INITIALIZE" in the advanced setup menu (see page 126). MAC Address (MAC (Media Access Control) address) This information displays the MAC address that is assigned to this unit. Status (Network status) This information displays the current link status of the network. Display status: 10BASE-T, 100BASE-TX, Full Duplex, Half Duplex, No Link Note English "No Link" appears when network connection is not made. Play Style (Playback styles) Use this feature to adjust the playback style according to your preference. You can shuffle songs in a random order or repeat one specific song or a sequence of songs. System (System ID) This information displays the system ID that is assigned to this unit. 95 En Graphical user interface (GUI) screen Manual Setup (Option) This menu adjusts the optional system settings. 1 Set the operation mode selector to D AMP and then press G SET MENU on the remote control. Press 4 k / n to select "Manual Setup" and then press 4 h. Press 4 k / n / l / h to select "Option" and then press 4 h. Scroll (Front panel display message scroll) Use this feature to set whether to display the information (such as song title or channel name) in the front panel display in a continuous manner or by the first 14 alphanumeric characters after scrolling all characters once when "XM", "DOCK" or "NET/USB" is selected as the input source. Choice Continue Functions Continuous mode. [. . . ] THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 16. 9. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). [. . . ]