User manual YAMAHA A-960 OPERATOR MANUAL

[. . . ] 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i. e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. [. . . ] · Use "MAX VOL. " in "ZONE SET" to set the initial volume level in Zone 2. y · You can also adjust the dynamic range of the bitstream signal sources by using "DYNAMIC RANGE" in "SOUND MENU" (see page 82). · This function is also useful for listening with your headphones. Note The adaptive dynamic range control feature does not function when this unit is in the Pure Direct mode (see page 52). Initial volume INIT. Use this feature to set the volume level of the main zone when the power of this unit is turned on. Choices: OFF, MUTE, ­80. 0 dB to +16. 5 dB Control step: 0. 5 dB Note The "MAX VOL. " setting takes priority over the initial volume setting. 80 En Customizing this unit (MANUAL SETUP) 3 SOUND MENU Use this feature to adjust the audio parameters. 3 SOUND MENU . A)EQUALIZER B)LFE LEVEL C)DYNAMIC RANGE D)LIPSYNC E)EXTD SUR. Graphic equalizer GEQ Use this feature to match the tonal quality of the center, surround L/R and surround back L/R, and surround back speakers with that of the front L/R speakers. You can adjust 7 frequency bands (63 Hz, 160 Hz, 400 Hz, 1 kHz, 2. 5 kHz, 6. 3 kHz, 16 kHz). Control range: ­6. 0 dB to +6. 0 dB Control step: 0. 5 dB A)EQUALIZER 1/2 A)EQUALIZER 2/2 [ ]/[ ]: Up/Down [ENTER]: Enter [ p TEST >OFF ON . CHANNEL;;;;FRONT L TEST >OFF ON CHANNEL;;;;FRONT L Equalizer A)EQUALIZER Use this feature to select the parametric equalizer or the graphic equalizer. Equalizer type select EQ TYPE SELECT Use this feature to select the type of equalizer. A)EQUALIZER EQ TYPE SELECT AUTO PEQ >GEQ [NATURAL] OFF 63Hz 160Hz 400Hz 1kHz [ ]/[ ]: Up/Down [p]/[[]: Select 0dB 0dB 0dB 0dB . 2. 5kHz 6. 3kHz 16kHz 0dB 0dB 0dB [ ]/[ ]: Up/Down [p]/[[]: Adjust [ [ y Press 9k / n to select a frequency band and 9l / h to adjust the selected frequency band. Note The "GEQ" parameter can be adjusted only when "GEQ" is selected in "EQ TYPE SELECT". [p]/[[]: Select [ENTER]: Enter Choice AUTO PEQ GEQ Functions Uses the parametric equalizer adjusted in "AUTO SETUP" (see page 33). Adjusts the built-in 7-frequency band graphic equalizer so that the tonal quality of the speakers matches. Use this feature to activate or deactivate the automatic lip sync. Choices: ON, OFF If the connected video monitor is compatible with the automatic lip sync: Select "ON". Use "AUTO" to make fine adjustments of the audio and video synchronization. If the video monitor is not compatible with the automatic lip sync or you do not want to use the automatic lip sync: Select "OFF". Use "MANUAL" to adjust the audio and video synchronization. Auto delay AUTO Use this feature to make fine adjustments of the audio and video synchronization when you set "HDMI AUTO" to "ON". Control range: 0 to 240 ms Control step: 1 ms y "offset" indicates the difference between the value of the audio delay that this unit sets automatically and the value of the audio delay that you set in "AUTO". This unit stores the value of "offset" and applies the value to other automatic lip sync compatible video monitors. Choice AUTO Functions Activates the optimum decoder to play back signals in 6. 1/7. 1 channels when this unit recognizes a signal flag being input. Plays back Dolby Digital or DTS signals in 7. 1 channels using the Pro Logic IIx movie decoder. Plays back Dolby Digital or DTS signals in 6. 1/ 7. 1 channels using the Pro Logic IIx music decoder. Plays back Dolby Digital or DTS signals in 6. 1/ 7. 1 channels using the Dolby Digital EX or DTSES decoder. [. . . ] Damage resulting from: (1) Repairs performed by the customer himself or by an unauthorised third party. (2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer's responsibility to ensure the product is adequately packaged when returning the product for repair. (3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha's instructions on the proper use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in the country where it is used. [. . . ]