User manual YAMAHA A3000V2E

[. . . ] Upgrade Guide for Version 2 1 Using this Upgrade Guide Using this Upgrade Guide This guide explains the new features and operating changes introduced with Version 2 of the A3000 Professional Sampler. Please use this guide as a supplement to your Owner's Manual, which is based on Version 1. Notations · This guide uses the following two symbols to refer to you appropriate pages. xx xx Refers you a page in the Owner's Manual. [. . . ] Note that the following Easy Edit settings cannot be transferred and are not reinitialized. (Under certain conditions various other settings may also be omitted from the transfer. ) If sample: If sample bank: MIDICtl (MIDI Control) setting. MIDICtl; Pitch page Fine setting; KeyLimit page RngShft (range shift), LoLimit, and HiLimit settings. · Push Knob 1 to execute the command. · Turn Knob 2 to select whether to target a single sample only (Smp) or else all samples and sample banks within the program (allSmp). · If you have selected Smp at Knob 2, use Knob 3 to select the sample or sample bank to be adjusted. 22 Chapter 2 Upgrade Reference Changes in PLAY MODE PLAY - PROGRAM - PgmSel [Select Program] 110 When you push Knob 4 (SAVE), the save type automatically sets to Pgm. When you press Knob 5 (ALL), the type sets to AllPgm(wp). PLAY - SAMPLE - SmpSel [Select Sample] 112 · You can turn Knob 5 to select any of four operations. You can push the knob to execute the operation. SAVE NEWBNK DELETE DUPL Jump to the standard SAVE command page. Create sample bank Delete currently selected sample or bank. Duplicate the currently selected sample or bank. · If you turn Knob 4 to switch ToPgm to off while Easy Edit settings are in effect, Version 2 will prompt for confirmation before proceeding to de-assign the sample. PLAY - SAMPLE - ToBank [Assign Sample to Bank] 115 If you select a sample that is already assigned to a program or to another sample bank, the following page will appear when you press Knob 5 (ADD). You can now select either of the following operations by turning the knob, and then execute by pushing the knob. DUPL&ADD MOVE&ADD Create a duplicate copy of the sample, and assign the duplicate to the selected sample bank. Remove the sample from its original program or sample bank and place it into the selected bank. Chapter 2 Upgrade Reference 23 Chapter 2 On Version 1, pushing Knob 4 (SAVE) or Knob 5 (ALL) moves you to a special page. On Version 2, these actions move you to the standard SAVE command page. Changes in PLAY MODE PLAY - EASY EDIT 119 Version 2 groups the Easy Edit parameters onto a number of pages so that they are easier to work with, and adds a few new parameters. The Easy Edit pages and parameters are as follows. Page Mix Output Filter Pitch AEGRate KeyLimit VelLimit Mode&Ctl Parameters Level, Pan, MIDI Receive Channel Main Output, Main Out level, Assignable Output, Assignable Out Level Cutoff, Distance, Q/Width, Gain Coarse, Fine AEG Attack Rate, Decay Rate, Release Rate Key Range Shift, Key Low Limit, Key High Limit, Key Crossfade Velocity Low Limit, Velocity High Limit, Velocity Crossfade Poly/Mono, Portamento, Alternate Group, MIDI Control PLAY - EFFECT - EfType 121 Knob 5 offers two new Connect settings: 1/2 3 and 1 2 3. 1/2 3 123 Output from Effect Block 2 passes through Effect Block 3. Output from Effect Block 1 and output from Effect Block 3 both pass through Effect Block 2. PLAY - EFFECT - In&Out1, In&Out2 126 Version 1's In&Out page has been renamed In&Out1, and a new In&Out2 page has been added. You can use the new page to set the width and output destination for each of the effect blocks. · Knob 3 sets the effect block's width (stereo expanse). · Knob 4 sets the block's output destination. On Version 1, output was always to the A3000 stereo outputs. On Version 2, you can direct the output to the stereo outputs, to any assignable-output pair, or to the digital output. Note that this setting is not available for any effect block whose output is directed to another effect block (as set up by the Connect parameter in the PLAY | EFFECT EfType page). 24 Chapter 2 Upgrade Reference Changes in PLAY MODE PLAY - SETUP - ADOut [Output Setup for A/D Input Signal] 134 PLAY - CONTROL - PgmCtl1 [Program Controller Setup 1] 136 · Knob 3 offers three additional "devices": Note Number, Velocity, and Program LFO. [. . . ] Parameter change The following messages have been added. Object link change 0 1 2 3 4 5 20 21 22 37 38 39 40 11110000 01000011 0001nnnn 01011000 00000100 0ccccccc 0ccccccc 0ttttttt 0ccccccc 0ccccccc 0ttttttt 0ddddddd 11110111 F0 43 nnnn = Device Number 58 04 upper object name (16 bytes) upper object type lower object name (16 bytes) lower object type data (0:link off, 1:link on) F7 This message changes the linking between the specified upper and lower objects (between program and sample, program and sample bank, or sample and sample bank). The message will not do anything if the current state of either specified object does not permit the link change, or if either object would need to be replicated to enable the link change. Appendix 43 Appendix Changes in MIDI Data Format 5. 3. 8. Object link request 0 1 2 3 4 5 20 21 22 37 38 39 11110000 01000011 0011nnnn 01011000 00000100 0ccccccc 0ccccccc 0ttttttt 0ccccccc 0ccccccc 0ttttttt 11110111 F0 43 nnnn = Device Number 58 04 upper object name (16byte) upper object type lower object name (16byte) lower object type F7 Returns Object-Link-Change Format message indicating the current linkage between the specified upper and lower objects. [. . . ]