User manual YAMAHA A4000

[. . . ] SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. [. . . ] Recording can also be started manually by pressing Knob 4 (>START) in the record standby display. Knob 1 [ [ Turn] Cursor Positions the cursor. Press] Tree View Calls the Tree View display (page 83). Knob 4 [ Turn] Start Edge Level Specifies the input level at which recording will be automatically started. Recording will start automaticall the instant the input signal level exceeds the Start Edge Level in the record standby display (but only if the Start Trigger parameter (Knob 3) is set to Edge/Manual). [Range] 0 -- 63 Knob 2 [ Press] MONITOR Pressing this knob alternately turns the MONITOR function on and off. A speaker icon appears above Knob 2 when the MONITOR function is turned on. Knob 3 [ Turn] AD Input Gain Selects line or microphone-level sensitivity for the analog input jacks. [Range] Line, Mic · If the front-panel REC VOL control is set to maximum (minimum) and the record level as displayed by the level meters is too low (high), set the AD Input Gain parameter to Mic (Line) for optimum level matching. [ Press] QUICK. . . Calls the quick entry menu (page 83). 158 Chapter 6 RECORD Mode · A5000/A4000 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Chapter 6 RECORD Mode RECORDING-TRIGGER Cursor e Cursor e Knob 1 Turn action Press action Cursor Tree View Knob 2 -- MONITOR Knob 3 Stop Trigger -- Knob 4 Stop Edge Level QUICK. . . Knob 5 -- -- Knob 1, 2 Same function as Cursor q (page 158). Knob 3 [ Turn] Stop Trigger Specifies the method to be used to stop recording in the record standby display. [Range] Manual, Edge/Manual · Manual . . . Recording can only be stopped by pressing Knob 5 (>FINISH) or Knob 2 (>STOP). Recording will stop automatically when the input signal level drops below the specified stop edge level (Knob 4). Recording can also be stopped manually by pressing Knob 5 (>FINISH) or Knob 2 (>STOP) in the record standby display. Knob 4 [ Turn] Stop Edge Level Specifies the input level below which recording will be automatically stopped. Recording will stop automaticall the instant the input signal level drops below the Stop Edge Level in the record standby display (but only if the Stop Trigger parameter (Knob 3) is set to Edge/Manual). [Range] 0 -- 63 [ Press] QUICK. . . Calls the quick entry menu (page 83). qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq A5000/A4000 · Chapter 6 RECORD Mode 159 RECORDING-EFFECT 4. EFFECT The EFFECT function sets the recording effect(s). If the recording-effect switch is enabled, the A5000/A4000 passes the incoming signal through the selected effect(s) before recording it into memory. · Most of the settings provided here are identical to those that you use to set up the program effects. The explanations below describe only those parameters that are different. For detailed information, refer to the explanations for the PLAY ­ EFFECT function. Recording Effect Edit [REC] Button [F4] Knob 1 to select "REC-EfEdit" In this display page it is possible to set the effect parameters for Effect 1 -- 3 (all effect parameters are available). · All functions are the same as in the PLAY mode EFFECT EDIT display (page 104). · Refer to the Effect Parameter List on page 258 for details on the parameters available for each effect. Press the [REC] button and then the [F4] button to enter the EFFECT function display. 2 display pages are provided: EfSetup (Effect Setup), and EfEdit (Effect Edit). Recording Effect Setup [REC] Button [F4] Knob 1 to select "REC-EfSetup" In this display page you can select the effect types for Effect 1 -- 3, and turn the record effects on or off. · In this display Knob 4 turns record effects on or off rather than selecting effect connections. All other functions are the same as in the PLAY mode EFFECT SETUP display (page 102). · Refer to the Effect List on page 256 for details on the available effect types. · When used as record effects, Effect 1 -- 3 are connected in series (1 2 3), and this arangement cannot be changed. Knob 1 Turn action Press action Cursor/Page Tree View Knob 2 Effect Type LIST. . . Knob 3 -- Effect1 BYPASS Knob 4 Rec Effect on/off Effect2 BYPASS Knob 5 -- Effect3 BYPASS Knob 4 [ Turn] Rec Effect on/off Turns record effects on or off. No record effects can be used when this parameter is turned off. [Range] off, 1>2>3 · Record effects cannot be used when the input is set to StOut, DIGITAL, or OPTICAL (page 155). 160 Chapter 6 RECORD Mode · A5000/A4000 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq RECORDING-EXT CTRL 5. EXT CTRL (External Control) This display page provides playback control of a CD loaded in a CD-ROM drive connected to the sampler's SCSI port. · To record from an audio CD loaded in the CD-ROM drive, be sure to connect the CD-ROM drive's analog audio outputs to the sampler's front-panel analog inputs. [. . . ] Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-703-0900 BRAZIL Yamaha Musical do Brasil LTDA. Rebouças 2636, São Paulo, Brasil Tel: 011-853-1377 DENMARK YS Copenhagen Liaison Office Generatorvej 8B DK-2730 Herlev, Denmark Tel: 44 92 49 00 PHILIPPINES Yupangco Music Corporation 339 Gil J. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 ARGENTINA Yamaha Music Argentina S. A. Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-371-7021 FINLAND F-Musiikki Oy Kluuvikatu 6, P. O. [. . . ]