User manual YAMAHA ACU16C

[. . . ] AMP CONTROL UNIT FRANÇAIS NETWORK HUB AND BRIDGE LINK CONDUCT NETWORK HUB and BRIDGE Owner's Manual Mode d'emploi Bedienungsanleitung Manual de instrucciones LOCK ERROR 88 M ESPAÑOL DEUTSCH ENGLISH ACU16-C/NHB32-C Owner's Manual Addendum Please make the following changes and additions to the ACU16-C/NHB32-C owner's manual. Some of these are due to the ACU16-C/NHB32-C system software upgrade, while others are corrections and supplementary explanations. Changes due to the software upgrade Support for CobraNet "Low Latency" (system software v1. 10) In conjunction with the upgrade to system software V1. 10, the latency setting that had been fixed at 5. 33 ms can now be selected from three choices (5. 33 ms/2. 67 ms/1. 33 ms). This allows even lower-latency distribution of audio signals. In addition, you can now make connections at the desired latency to digital mixers such as the PM5D or digital mixing engines such as the DME64N/24N via the Yamaha "MY16-C" card. [. . . ] Click OK to close the System Properties window, and then click the Close button to close the Control Panel window. Turn off the ACU16-C/NHB32-C and use a USB cable to connect the USB port on the ACU16-C/NHB32-C to a USB port on your computer. Select "Install software automatically (recommended) (I), " and then click Next. The driver is installed, and the message "Completing the Found New Hardware Wizard" appears. Click Finish, and then restart your computer. 4 5 6 7 8 ACU16-C & NHB32-C Owner's Manual ENGLISH 1 Start your computer and Windows, and insert the included CD-ROM into your computer's CD-ROM drive. 18 NetworkAmp Manager Installation Installing the Yamaha CBX Driver If you are connecting the ACU16-C/NHB32-C to a serial port on your computer, you'll need to install the Yamaha CBX driver. If you already have this software installed, skip this section. Computer NetworkAmp Manager Serial cable Yamaha CBX driver ACU16-C/NHB32-C 1 2 3 Double-click the "Mididrv_" folder on the CD-ROM. Double-click "Setup. exe. " Follow the on-screen instructions to install the software. When prompted to "Select the number of MIDI output ports, " choose "Use single MIDI output port. " When the message "Do you want to configure Windows to use the YAMAHA CBX A Driver as the default MIDI output device?" appears, click No. When the message "Set the HOST SELECT switch on a tone module to PC-2. Connect the TO HOST terminal on a tone module to the computer's COM port. " appears, you can ignore it because the ACU16-C/NHB32-C does not have a HOST SELECT switch or port. Installing NetworkAmp Manager 1 2 Locate the "NetworkAmp Manager" folder on the CD-ROM. Copy the "NetworkAmp Manager" folder to your hard disk. To uninstall NetworkAmp Manager, simply delete or drag the "NetworkAmp Manager" folder to the Recycle Bin. Starting NetworkAmp Manager To start NetworkAmp Manager, simply double-click the NetworkAmp Manager icon. When you start NetworkAmp Manager, the Open Project dialog box appears. To create a new project, click Cancel and, on the subsequent dialog boxes, enter a name and select a location for the new project and its folder. For information on how to use NetworkAmp Manager, refer to the PDF Network Amp Manager Owner's Manual, which can be opened directly from NetworkAmp Manager's Help menu. Installation Troubleshooting · · · Cannot install the Yamaha USB MIDI Driver Is the USB cable connected correctly (page 11)?Try disconnecting the USB cable, and then reconnecting it. When the ACU16-C/NHB32-C is connected to your computer for the first time, if the Add New Hardware Wizard doesn't appear, it may be because your computer's USB controller is disabled. To check this, open the System control panel, click the Device Manager tab, and check for any crosses (x) or exclamation marks (!) next to the "Universal Serial Bus controllers" and "USB Root Hub" items. If these items do have these marks next to them, your USB controller is disabled. For information on enabling your USB controller, refer to your computer's documentation. ACU16-C & NHB32-C Owner's Manual Installation Troubleshooting 19 · If for some reason installation of the Yamaha USB Driver fails, the ACU16-C/NHB32-C may be registered as an unknown device and you may not be able to reinstall the driver until the unknown device is deleted. In this case, open the System control panel, click the Device Manager tab, and select the "View devices by connection" option. If an item called "Other devices" appears in the list, click it. [. . . ] This means that the NHB32-C cannot lock to the currently selected wordclock source. Check and correct the source, or select another. This indicates that a patch other than the one recalled or stored last is selected. Recall the patch, or select the patch that was last recalled or stored in order to stop it flashing. [. . . ]