User manual YAMAHA AUDIOGRAM3

[. . . ] EN DE FR ES RU JA Español Français Deutsch Owner's Manual Bedienungsanleitung Mode d'emploi Manual de instrucciones English USB AUDIO INTERFACE COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Address : Telephone : Type of Equipment : Model Name : Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. 90620 714-522-9011 COMPUTER RECORDING SYSTEM AUDIOGRAM 3 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (FCC DoC) FCC INFORMATION (U. S. A. ) 1. [. . . ] Click the [Edit] button ( ) on the left side of the channel strip to open the VST audio channel settings window. Click Insert 1 and select Earlier VST Plug-ins Reverb RoomWorks SE. NOTE For further details refer to the pdf manual provided with the Cubase AI software. It's a good idea to lower the channel fader a bit before adding an effect, since the effect can cause an increase in the overall channel level. CAUTION 6 When the final mix adjustments have been made, go to the [File] menu and select [Export] [Audio Mixdown]. 16 AUDIOGRAM 3 Owner's Manual Quick Guide 7 Enter a file name and select a destination for the file as well as a file type. If you intend to use the file to create an audio CD, select the WAV file type (AIFF on Macintosh OS X), Stereo Out (stereo), 44. 1 kHz, and 16 bit. 8 Click [Export]. Progress of the mixdown operation will be shown in a progress window. When the progress window closes the mixdown is complete. NOTE Files created by mixdown can be directly played back using the Windows Media Player, or iTunes. AUDIOGRAM 3 Owner's Manual 17 Controls and Functions Control Panel u q ew e t yr 1 PHANTOM +48V Switch/Indicator This switch toggles phantom power on and off. If you set the switch on ( ), the AUDIOGRAM supplies phantom power to the MIC/INST jack (XLR-type) 8. Turn this switch on when using a phantom-powered condenser microphone. · Be sure to leave this switch off ( ) if you do not need phantom power. · When turning the switch on, be sure that only a condenser microphone is connected to the MIC/ INST input jack. Other devices may be damaged if connected to phantom power. This precaution does not apply to balanced dynamic microphones or instruments with the phone jack, however, as these will not be affected by phantom power. · To prevent damage to speakers, be sure to turn off audio system (monitor speakers) before turning this switch on or off. We also recommend that you set the OUT LEVEL control to the minimum position. Neglect of these precautions may result in large noise bursts that may damage your equipment, your ears, or both. 3 LEVEL Controls Adjusts the level of the channel signal. Use these controls to adjust the balance between the channels. 4 POWER Indicator This indicator lights when power is applied to the AUDIOGRAM interface via the USB cable (supplied) that connects it to the computer. CAUTION 5 Level Indicators These indicators show signal levels prior to the OUT LEVEL control 6. The SIGNAL LED lights when a signal is present, and the PEAK LED lights when the signal reaches or exceeds clipping level. Adjust the input channel LEVEL controls 3 so that the PEAK LEDs flash only briefly on occasional high-level peaks or not at all. 6 OUT LEVEL Control Adjusts the signal level sent to the STEREO OUT jacks 0. This allows you to adjust the overall volume without changing the relative volume balance among the channels. When connecting or disconnecting the USB or audio cables be sure to turn the OUT LEVEL control all the way down. CAUTION 7 USB Connector Connects the AUDIOGRAM interface to a USB port on your computer via the supplied USB cable. In addition to transferring audio data between the AUDIOGRAM interface and the computer, the USB cable supplies power from the computer to the AUDIOGRAM interface. Yamaha recommends that you NOTE use a USB cable with a length of 1. 5 meter or less. 2 MIC/INST Switch Set this switch according to the type of device connected. Select MIC ( ) if a microphone is connected, or INST ( ) if an electric guitar or bass is connected. If a device is not connected to the NOTE MIC/INST jack, set this switch to MIC ( ). [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. OTHER COUNTRIES Yamaha Music Gulf FZE LOB 16-513, P. O. Box 17328, Jubel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Central Europe GmbH Sp. z. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]