User manual YAMAHA AW4416

[. . . ] PROFESSIONAL AUDIO WORKSTATION Operation Guide E FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] Press the [SETUP] key ¡ [F1] (Patch IN) key. The display will show the SETUP screen Patch IN page, where you can patch signals to the input channels and recorder inputs. In this page, the MIXER CHANNEL INPUT ASSIGN column shows the patched status of input channels 1­24 and return channels 1/2. Tip! If the Patch IN tab is not assigned to the [F1] key, press the [SHIFT] key + [F1] key to switch the tabs, and then press the [F1] key. -- Operation Guide 133 Chapter8--Patching 1 2 1 Input channels 1­24 B Return channels 1/2 2. Move the cursor to the channel that you wish to patch, and use the [DATA/JOG] dial to select the signal that you wish to assign. The following signals can be assigned to each channel. Input channels 1­24 Display AD 1 ­ AD 8 SL1-1 ­ SL1-8 SL2-1 ­ SL2-8 DIN L/DIN R SMP 1 ­ SMP 8 MET INPUT jacks 1­8 INPUT 1­8 of an I/O card (slot 1) INPUT 1­8 of an I/O card (slot 2) L/R channels of the DIGITAL STEREO IN jack Sampling pads 1­8 Internal metronome Type of signal Return channels 1/2 Display EFF 1 L/R EFF 2 L/R AD 1/2 ­ AD 7/8 SL1-1/2 ­ SL1-7/8 SL2-1/2 ­ SL2-7/8 DIN L/R *1. Selectable only for return 2 Type of signal Return from internal effect 1*1 Return from internal effect 2*2 INPUT jacks 1/2­7/8 INPUT 1/2­7/8 of an I/O card (slot 1) INPUT 1/2­7/8 of an I/O card (slot 2) DIGITAL STEREO IN jack (stereo) Tip! You can use the patch library to save the state of the patch settings you make. For details refer to page 138. 134 -- Operation Guide Chapter8--Patching Patching to the recorder inputs When the AW4416 is in the default state, buses 1­8 are assigned respectively to recorder inputs 1­8 and 9­16, but you can assign the direct signals from the input channels as desired. Recorder input patch ×8 ×8 Mixer section Buses 1­8 Recorder section Tracks 1­8 Tracks 9­16 Here's how to assign the desired signals to recorder inputs 1­16. 1. Press the [SETUP] key ¡ [F1] (Patch IN) key to access the SETUP screen Patch IN page. The RECORDER TRACK INPUT ASSIGN column will indicate the patched status of recorder inputs 1­16. Tip! If the Patch IN tab is not assigned to the [F1] key, press the [SHIFT] key + [F1] key to switch the tabs, and then press the [F1] key. RECORDER TRACK INPUT ASSIGN column 2. Move the cursor to the recorder input whose patching you wish to change, and use the [DATA/JOG] dial to select the signal that you wish to assign. The following types of signal can be assigned to each input. Recorder inputs 1­16 Display BUS 1 ­ BUS 8 DIR 1 ­ DIR16 Buses 1­8 Input channel direct out 1­16 Type of signal -- Operation Guide 135 Chapter8--Patching Patching to the outputs When the AW4416 is in the default state, the following signals are assigned to the OMNI OUT jacks, STEREO OUT jacks, and digital I/O card outputs. If necessary, you can change the output signals that are assigned to these output jacks. Mixer section AUX buses 1­4 Stereo output channel Output patch ×4 ×2 ×2 ×8 ×8 OMNI OUT jacks 1­4 DIGITAL STEREO OUT jack STEREO OUT jacks OPTION I/O slot 1 OPTION I/O slot 2 I/O card I/O card Buses 1­8 Here's how to assign the desired signal to each output jack. 1. Press the [SETUP] key ¡ [F2] (Patch OUT) key. The display will show the SETUP screen Patch OUT page. The various fields of the display will show the patched status of each output jack. Tip! If the Patch OUT tab is not assigned to the [F2] key, press the [SHIFT] key + [F1] key to switch the tabs, and then press the [F2] key. 1 2 4 5 3 1 OMNI OUT jack 1­4 B DIGITAL STEREO OUT jack C STEREO OUT jack D OUTPUT 1­8 of an I/O card (slot 1) E OUTPUT 1­8 of an I/O card (slot 2) 136 -- Operation Guide Chapter8--Patching 2. Move the cursor to the output jack whose patching you wish to change, and use the [DATA/JOG] dial to select the signal that you wish to assign. The following types of signal can be assigned to each output jack. OMNI OUT jacks 1­4 Display AUX 1 ­ AUX 8 RDR 1 ­ RDR16 ST L/ST R BUS 1 ­ BUS 8 DIR 1 ­ DIR16 AUX buses 1­8 Recorder direct out 1­16 L/R channels of the stereo output channel Buses 1­8 Input channel direct out 1­16 Type of signal DIGITAL STEREO OUT jack STEREO OUT jacks Display ST L/R BUS 1/2 ­ BUS 7/8 DIR 1/2 ­ DIR15/16 AUX 1/2 ­ AUX 7/8 RDR 1/2 ­ RDR15/16 Type of signal Stereo output channel Buses 1/2­7/8 Input channel direct out 1/2­15/16 AUX buses 1/2­7/8 Recorder direct out 1/2­15/16 Digital I/O card (slot 1) OUTPUT 1­8 Digital I/O card (slot 2) OUTPUT 1­8 Display BUS 1 ­ BUS 8 DIR 1 ­ DIR16 AUX 1 ­ AUX 8 RDR 1 ­ RDR16 ST L/ST R Buses 1­8 Input channel direct out 1­16 AUX buses 1­8 Recorder direct out 1­16 L/R channels of the stereo output channel Type of signal Tip! When selecting a signal for assignment to an output jack, selections beginning with "I-" such as "I-I8" or "I-M16" may be displayed in gray. Selections beginning with "I-" indicate insert-out points of each channel. The gray display indicates that this insert point is invalid. (For details on insert I/O patching, refer to page 140. ) -- Operation Guide 137 Chapter8--Patching Patch library Patch settings that you make in the SETUP screen Patch IN page and Patch OUT page can be stored in the patch library as one of twenty patch programs. The contents of the patch library are saved on the internal hard disk as part of the song. Here's how to use the patch library. Storing to the patch library Here's how to assign a name to your patch settings, and store them in the patch library. 1. [. . . ] In this case, additional data can be recorded later on the ejected CD-R media. 262 -- Operation Guide Chapter17--Mastering Finalizing As long as you have not executed the Finalize operation, other stereo track data can be added to CD-R media that was recorded using Track At Once. However, media that has not yet been finalized cannot be played back by a CD-RW drive or a conventional CD player. In order to use a CD player to play CD-R media on which you have written data, use the following procedure to execute the Finalize operation. 1. Place the CD-R media that you wish to finalize on the CD-RW drive tray. [. . . ]