User manual YAMAHA AX-V401

[. . . ] Natural Sound Stereo Integrated Amplifier Préampli/ampli de puissance stéréo de la série "Natural Sound" AX-V 401 Natural Sound Stereo-Verstärker Natural Sound Integrerad Stereo Förstärkare Amplificatore integrato stereo a Suono Naturale Amplificador integrado estéreo de Sonido Natural Natural Sound Geïntegreerde Stereo Versterker S OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTE ZUBEHÖRTEILE MEDFÖLJANDE TILLBEHÖR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES q q q q q q q q q q q q q q After unpacking, check that the following parts are contained. Après le déballage, vérifier que les pièces suivantes sont incluses. Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. Kontrollera effer det apparaten packats upp att följande delar finns med. [. . . ] Simply insert the Banana Plug connector into the corresponding terminal. How to Connect: Red: positive (+) Black: negative (­) 2 3 1 Unscrew the knob. 5mm (1/4") insulation from the speaker wires. ] Tighten the knob and secure the wire. ABOUT THE ACCESSORY TERMINALS AC OUTLETS (Europe and General models). . . . . . . . . . . . . 3 SWITCHED OUTLETS (Australia and U. K. models). . . . . . . . . . . . . . . . . . . 1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit's POWER switch or the provided remote control transmitter's POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100 watts (200 watts for General model only). REMOTE CONTROL (PHONO) connector If you have a YAMAHA turntable with the mark, connect it to this connector by using the cable provided with the turntable. This connection allows you to control the turntable from the provided remote control transmitter. GND terminal (For turntable use) Connecting the ground wire of the turntable to this terminal will minimize hum, but in some cases better results may be obtained with the ground wire disconnected. 5 OPERATIONS 2 4 3 1, 6 TO PLAY A SOURCE 7 5 6 0 1 VOLUME Play the source. VOLUME -- dB Set to the " " position. -- dB 0 2 POWER Adjust to the desired output level. 7 3 Select a desired input source. (For video sources, turn the TV/monitor ON. ) MONITOR VCR/TAPE 2 TAPE 1 LD/TV TUNER If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS controls, etc. (Refer to page 8. ) INPUT CD PHONO COPY * The indicator corresponding to the selected input source will illuminate. * Note that pressing on each input selector selects the source which is connected to the corresponding input terminals on the rear panel. 4 Select the speakers to be used. SPEAKERS A ON Note In the step 3, if two or more program sources are selected at the same time (by using input selectors), be sure to remember the priority order of the input sources. Priority order of audio sources: 1) TAPE 1, 2) VCR/TAPE 2, 3) LD/TV, TUNER, CD or PHONO. Priority order of video sources: 1) VCR/TAPE 2 , 2) LD/TV. q If you select LD/TV, TUNER, CD or PHONO, be sure that TAPE 1 and/or VCR/TAPE 2 are not being selected. q If you select TAPE 1 and VCR/TAPE 2, and another input selector at the same time, the result will be the visual of VCR/TAPE 2 and the sound from TAPE 1. q If you select both LD/TV and TAPE 1 at the same time, the result will be the visual of LD/TV and the sound from TAPE 1. q Once you play the LD player, its visual will not be interrupted even if other input selectors except VCR/TAPE 2 are selected. B ON OFF OFF * If you use two speaker systems, press both the A and B switches. 6 ENGLISH 1, 4 2 TO RECORD A SOURCE TO TAPE 1 Select the source to be recorded. MONITOR VCR/TAPE 2 TAPE 1 LD/TV TUNER INPUT CD PHONO COPY Notes q VOLUME, BASS, TREBLE, BALANCE and LOUDNESS control settings have no effect on the material being recorded. q To dub from tape to tape, only the following one way of dubbing can be performed. Note that when dubbing is performed from a VCR to an audio tape deck, only audio signals of the VCR will be dubbed to the audio tape deck. SOURCE RECORDER * To dub from tape to tape, refer to the "Notes" shown below. If the CD player, tuner, turntable, equalizer, and tape deck connected to this unit are YAMAHA components designed for remote control compatibility (components with an S mark), then this remote control transmitter will also control various functions of each component. Please consult YAMAHA dealer for information on which components are compatible with the remote control transmitter. ENGLISH KEY FUNCTIONS For Control of This Unit Turns the power on/off. PLAY/CUT SKIP POWER PHONO PLAY CD SEARCH PAUSE/STOP DISC SKIP -- -- PRESET + + A/B/C/D/E TUNER EQ PRESET EQ ON/FLAT LD/TV Selects input source. DIR A DECK A/B DIR B TAPE 1 PLAY MONITOR REC PAUSE STOP REC MUTE VCR/TAPE 2 Turns the volume level up/down. -- VOLUME + For Other Component Control Identify the remote control transmitter keys with your component's keys. If these keys are identical, their function will be the same. [. . . ] The distance or range within which the remote control transmitter can be used decreases. The sound is degraded when monitoring is performed by using the headphones connected to the compact disc player or cassette deck which are connected with this unit. The record is being played on a turntable with an MC cartridge. Direct sunlight or lighting (of an inverter type of flourescent lamp etc. ) is striking the remote control sensor of the main unit. [. . . ]