User manual YAMAHA B45

[. . . ] • The screen displays as illustrated in this owner’s manual are for instructional purposes, and may appear somewhat different from the screens which appear on your computer. • For information on modification of system software, certain functions, or specifications due to version update of the application, please visit the following website: http://www. yamahaproaudio. com/ • Windows is a registered trademark of Microsoft® Corporation in the U. S. • Apple, Mac and Macintosh are trademarks of Apple Inc. , registered in the U. S. • The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies. Contents Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] An indication of “H” will appear on the EQ graph of the equalizer. 4 Ø (Phase) Inverts the phase polarity of the signal after AD conversion. 5 GC (Gain Compensation) This is an on/off switch for the head amp’s analog gain correction. If you want to share the same I/O rack with the multiple CL consoles, this function maintains the audio signal at a specific level throughout the network. This button will be displayed only if the DANTE ports have been patched. 27 CL Editor Owner’s Manual ❏ TO STEREO/MONO Here you can specify how the signal will be sent from the input channel to the STEREO bus/MONO bus. MODE • ST/MONO button When this button is on, the signal will be sent to the STEREO L/R bus and independently to the MONO bus. [INPUT CH 1–72] [ST IN channel 1–8] PAN (PAN/BALANCE for ST IN) The PAN knob adjusts the panning of the signal sent from the input channel to the STEREO bus L/R channels. You can set this to the center position by holding down the <Ctrl>(< >) key of the computer keyboard and clicking the knob. You can select Pan or Balance for ST IN. The BALANCE knob adjusts the balance of the signal that is sent from the ST IN channel to the STEREO bus L/R channels. PAN/BALANCE can be switched with the [PAN]/[BALANCE] buttons. Switches the signal sent from the input channel to the STEREO bus on/off. Switches the signal sent from the input channel to the MONO bus on/off. ST M(C) • LCR button When this button is on, the signal will be sent to the L/C/R buses which work in conjunction with each other. [INPUT CH 1–72] [ST IN channel 1–8] The PAN knob adjusts the panning of the signal that is sent from the input channel to each of the L/C/R channels. You can set this to the center position by holding down the <Ctrl>(< >) key of the computer keyboard and clicking the knob. You can select Pan or Balance for ST IN. The expander effect will apply to levels below THRESHOLD + WIDTH. 32 CL Editor Owner’s Manual 7 RATIO Specifies the ratio (the amount of compression. ) 8 WIDTH Specifies the width between the threshold level of the compressor (THRESHOLD) and the threshold level of the expander. 9 ATTACK Specifies the time (the attack time) until it starts to compress and expand the input signal once the compander has been triggered. 0 GAIN Adjusts the gain of the signal after it has passed through the compander. A RELEASE Specifies the time (the release time) from when the key-in signal falls below the threshold level until compression and expansion are removed. B KEY IN SOURCE Click this to select the key-in signal that you want to use. The choices are the same as for GATE. If DE-ESSER is selected 5 1 2 3 6 7 8 4 9 0 1 TYPE This indicates that De-Esser is the currently selected type. 2 LIBRARY This button accesses the dynamics library. Clicking this button will open the DYNAMICS page of the Library window. 3 ON This button switches the de-esser on/off. 4 Response curve Indicates the response for the de-esser of the currently selected channel. 5 GR meter (Gain Reduction meter) This meter indicates the amount of gain reduction produced by the de-esser. 6 THRESH (Threshold level) Specifies the threshold level at which the de-esser will operate. The input signal will start being compressed when the key-in signal exceeds this level; compression will be removed when the signal falls below this level. 7 FREQ (Minimum frequency/Center frequency) Specifies the minimum frequency (for HPF) or the center frequency (for BPF) at which the key-in signal will activate the de-esser. 33 CL Editor Owner’s Manual 8 TYPE Drag the knob in the screen to select the HPF (High Pass Filter) or BPF (Band Pass Filter. ) 9Q Adjust the Q level of the frequency range at which the key-in signal will activate the de-esser. 0 KEY IN SOURCE The key-in signal is set to the SELF POST EQ. ❏ DELAY 1 2 1 ON Turns the delay on/off of the currently selected channel. 2 Delay time Drag the knob in the screen to adjust the delay time of the currently selected channel. ❏ INSERT (except for ST IN channels) 1 4 5 6 2 1 ON Enables/disables insert-in/out. 3 2 OUT (Insert out) Click this to select the output port that will be assigned to insert-out, from the following choices. NONE OMNI 1-OMNI 8 SLOT1-1, SLOT1-2. . . SLOT3-15, SLOT3-16 FX1L(A), FX1R(B). . . FX8L(A), FX8R(B) PR1L(A), PR1R(B). . . PR8L(A), PR8R(B) No assignment OMNI OUT jacks 1–8 Output channels of an I/O card installed in slots 1–3 L/R inputs of EFFECT rack 1–8 L/R inputs of PREMIUM rack 1–8 3 IN (Insert in) Click this to select the input port that will be assigned to insert-in, from the following choices. NONE OMNI 1-OMNI 8 SLOT1-1, SLOT1-2. . . SLOT3-15, SLOT3-16 FX1L(A), FX1R(B). . . FX8L(A), FX8R(B) PR1L(A), PR1R(B). . . PR8L(A), PR8R(B) No assignment OMNI IN jacks 1–8 Input channels of an I/O card installed in slots 1–3 L/R outputs of EFFECT rack 1–8 L/R outputs of PREMIUM rack 1–8 4 POINT (Insert point) Selects the position at which insert-in/out will be patched. Choose from PRE EQ, PRE FADER, or POST ON. 34 CL Editor Owner’s Manual 5 HA (HA analog gain) Adjusts the analog gain for OMNI IN. This knob appears only if you select OMNI as INSERT IN (3). 6 48V (Phantom power) Switches phantom power (+48V) on/off. This button appears only if you select OMNI as INSERT IN (3). ❏ DIRECT OUT (except for ST IN channels) 1 2 1 ON 3 4 Turns the direct output on/off. You can right-click (<control> key + click) the button to display a popup menu and select ALL ON or ALL OFF. 2 DIRECT OUT GAIN Adjusts the gain of the direct output. The current value is shown in the numerical box below the knob. You can set this to the nominal value (0. 0 dB) by holding down the <Ctrl>(< >) key and clicking the knob. 3 DIRECT OUT PORT Click this to select one of the following output ports as the one used for direct out. NONE DANTE 1–DANTE 64 OMNI 1–OMNI 8 REC L, REC R SLOT1-1, SLOT1-2. . . SLOT3-16 No assignment DANTE OUTPUT 1–64 OMNI OUT jacks 1–8 L/R inputs of RECORDER Output channels of an I/O card installed in slots 1–3 4 DIRECT OUT POINT Selects the position at which direct out will be patched. Choose from PRE HPF, PRE EQ, PRE FADER, or POST ON. ❏ RECALL SAFE/MUTE SAFE These enable/disable Recall Safe and Mute Safe for the channel. 35 CL Editor Owner’s Manual ❏ DCA GROUP/MUTE GROUP 3 3 1 DCA GROUP Selects the DCA group (1–16) to which that channel belongs. 2 MUTE GROUP Selects the mute group (1–8) to which that channel belongs. 3 DCA/MUTE 1 2 These buttons enable/disable DCA group and Mute group for the channel. ❏ Fader 1 1 ON Switches the input channel on/off. [. . . ] 36 DE-ESSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 39 Fader . . . . . . . . . . . . . . . . . . . . . . . . . 36, 40, 42, 44 FROM MIX, ST/MONO(C) . . . . 27 Input channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 INSERT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]