User manual YAMAHA B75E

[. . . ] If you must use an extension cord, the minimum wire size for a 25' cord (or less ) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. [. . . ] This feature can be used for music production as well as performance. Triggering the Arpeggio 1 Press the [ARPEGGIO] button to turn on the Arpeggio function. Changing the Arpeggio Type The most suitable Arpeggio Type is automatically selected when you select a Main Voice, but you can easily select any other Arpeggio Type. Flute 148 Quick Guide 1 Hold down the ARPEGGIO [TYPE] button for longer than a second. In the display, "ARP Type" appears for a few seconds, followed by the current Arpeggio Type appears. NOTE · Selecting a Voice number between 230 and 269 will turn on Arpeggio automatically. DownOct Hold for longer than a second. 2 Press a note or notes to trigger Arpeggio. The Arpeggio phrase differs depending on the number of pressed notes and the area of the keyboard. 002 The currently selected arpeggio type 2 Rotate the dial to select the desired Arpeggio type An Arpeggio Type List is provided in the separate Data List. When Split is on, Arpeggio is applied only to the Split Voice. When Split is off, Arpeggio is applied to the Main and Dual Voices. Arpeggio cannot be applied to the Split and Main/Dual Voices simultaneously. For instructions on selecting a Split Voice, refer to page 36. Note that selecting one of the Main Voices 260­ 269 will call up the appropriate Split Voice. NOTE · When you select a Voice between 260 and 269, play a key to the left of the Split Point, since Arpeggio is applied only to the Split Voice. · When an optional Footswitch (page 13) connected to the SUSTAIN jack is pressed, the Arpeggio will continue to play after the note is released (page 39). 3 To turn off the Arpeggio, press the [ARPEGGIO] button again. 20 B75E Owner's Manual Creating Original Sounds via the Knobs The two knobs located in the lower left area of the panel can be used to add variations to the sound being played, transforming the sound in a variety of musical ways. Select the desired pre-programmed effect combination printed above the Knobs, then rotate the Knobs to enjoy the sound. Selecting a Knob Effect Combination Repeatedly press the [ASSIGN] button to sequentially select the five effect combinations provided: (1) (2) (3) (4) (5) (1) . . . The current combination is shown in the display. Applying the Filter to the Main Voice 1 2 3 Select the desired Main Voice. Here, select "164 SquareLd" (Square-wave Lead) as a synth-lead type Voice. Includes traditional Songs from around the world. Songs transferred from a computer (refer to "Computer-related operations"--page 9) and Songs in the USB flash memory (page 53). Quick Guide Listening to a Demo Song Press the [DEMO] button to play Songs in sequence. Playback will repeat continuously, starting again from the first Song (001). Selecting and Playing Back a Song 1 Press the [SONG] button, then use the dial to select the desired Song. Refer to the Song List in the Data List (page 9). To stop playback, press the [DEMO/BGM] button. ForElise 015 Current Song 2 Press the [ ] (Start/Stop) button to start playback. To stop playback, press the [ ] (Start/Stop) button again. ForElise 015 Each arrow mark flashes in time with the beat. 24 B75E Owner's Manual Playing Songs Song Fast Forward, Fast Reverse, and Pause Like the transport controls on an audio player, this instrument lets you fast forward [ ] (Fast Forward), rewind [ ] (Fast Reverse) and pause [ ] (PAUSE) playback of the Song. Fast Forward During playback, press this button to rapidly skip ahead to a later point in the Song. 3 When playback reaches to the point you want to specify as the end point, press the [ ] (A-B REPEAT) button again to set the B point. The specified A-B section of the song will now play repeatedly. To cancel repeat playback, press the [ ] (A-B REPEAT) button. To stop playback, press the [START/STOP] button. NOTE 4 · If you want to set the start point "A" at the top of the Song, press the [ ] (A-B REPEAT) button before starting playback. Turning Each Track On/Off Fast Reverse During playback, press this button to rapidly return to an earlier point in the Song. Pause During playback, press this button to pause playback, and press again to start from that point. Each "track" of a Song plays a different part--melody, percussion, accompaniment, etc. Each of the tracks can be muted so that you can play the muted part yourself. Pressing the desired Track button repeatedly will toggle the on/off status. NOTE · When the A-B repeat is specified, the Fast Reverse and Fast Forward will only work within the range between A and B. A-B Repeat You can play back only a specific section of a Song repeatedly by setting the A point (start point) and B point (end point) in one-measure increments. Track number on--Track will playback A B NOTE Track number off--Track is muted or contains no data · Up to two Track buttons can be pressed simultaneously for turning on or off. 1 2 Start playback of the Song (page 24). [. . . ] Determines how much of the Split Voice's signal is sent to the Reverb effect. Determines how much of the Split Voice's signal is sent to the Chorus effect. 032 033 Reverb Depth Chorus Depth S. Reverb S. Chorus * * Effects 034 035 036 Reverb Type Chorus Type Master EQ Type Reverb Chorus MasterEQ 01­10 01­05 Speaker, Boost, Headphone, Line Out1, Line Out2 1­3 ** ** 1 (Speaker) Refer to page 33. Higher values produce a greater Wide effect. 037 Wide Type Wide 2 (Wide2) Harmony (page 19) 038 039 Harmony Type Harmony Volume HarmType HarmVol 01­26 000­127 * * Determines the Harmony type. Determines the volume of the Harmony effect Arpeggio (page 20) 040 Arpeggio Type ARP Type 001­150 * Determines the Arpeggio type. [. . . ]