User manual YAMAHA C-85

[. . . ] 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i. e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. [. . . ] Selects the initial input mode of the source. Adjusts the HDMI support audio. Features Page 88 88 91 91 91 91 92 Auto Setup (Auto setup menu) Use to run AUTO SETUP and specify which speaker parameters to be adjusted (see page 32). System Memory (System memory menu) Use to save and recall various settings (see page 92). Signal Info. (Signal information menu) Use to check signal information (see page 45). Language (GUI language menu) Use to select the language of your choice that appears in the GUI (graphical user interface) menu of this unit (see page 93). y You can also select the GUI language using the LANG. parameter in ADVANCED SETUP in the front panel display (see page 95). ADVANCED OPERATION English 71 SYSTEM OPTIONS Changing parameter settings Use the remote control to access and adjust each parameter. (Speaker set is used in the following example to change parameter settings. ) Manual Setup > Basic > Speaker Set > AMP 3 Press k / n repeatedly to select the parameter you want to adjust. Presence Bass Out Bass Cross Over SWFR Phase 40Hz 60Hz 80Hz (THX) 90Hz 100Hz + TV VOL + CH + SOURCE VOLUME ­ TV MUTE ­ TV INPUT PRESET ­ MUTE EXIT TV 1 5 2-4 4 1 GUI TOP PURE DIRECT TITLE BAND MENU NIGHT ENTER A/B/C/D/E AUDIO STRAIGHT RETURN DISPLAY EFFECT Press ENTER or h and then press k / n repeatedly to change the setting of the item you want to adjust. Presence Bass Out Bass Cross Over SWFR Phase 40Hz 60Hz 80Hz (THX) 90Hz 100Hz 1 Set AMP/SOURCE/TV to AMP and then press GUI TOP on the remote control. The top display appears. AMP GUI TOP SOURCE TV TITLE BAND 5 Stereo/Surround Input Select Manual Setup Auto Setup System Memory Sound Video Basic Option Press EXIT. y If you want to continue adjusting parameter settings, press ENTER to return to the previously selected menu item. Notes · The available parameters may be displayed on more than one page of the GUI display. · You cannot change parameter values when Memory Guard is set to "On". If you want to change the parameter values, set Memory Guard to "Off" (see page 91). 2 Press k / n repeatedly to select a menu and then press h to enter the selected menu. Test Tone Speaker Set Speaker Distance Speaker Level Front Center Surround Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cable is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter values will return to the factory settings. If this happens, edit the parameter value again. Front Center Surround Surround Back Presence Large Small None 72 SYSTEM OPTIONS Input Select Use this feature to reassign digital input/outputs, select the input signal, rename the inputs, or adjust the level of the signal input at each jack. You can select the type of input signal you want to use. Input Select > input source (DVD, etc. ) > Audio Select > Choices: Auto, HDMI, Coax/Opt, Analog Decoder Mode (Decoder mode) Use this feature to switch the input mode. You can designate the reassigned digital input jacks (see page 74) for specific audio signals (DTS, etc. ). Input Select > input source (DVD, etc. ) > Decoder Mode > Choices: Auto, DTS I/O Assignment Audio Select Decoder Mode Volume Trim Auto DTS I/O Assignment Audio Select Decoder Mode Volume Trim Auto HDMI Coax/Opt · Select "Auto" if you want signals to be input to this unit in the following order: HDMI signals, digital signals* and analog signals. · Select "HDMI" if you only want HDMI signals to be input to this unit. If no HDMI signals are input, no sound is output. · Select "Coax/Opt" if you want digital signals to be input to this unit at the OPTICAL or COAXIAL jacks. Use if HDMI signals are also being input. · Select "Analog" if you only want analog signals to be input to this unit. If no analog signals are input, no sound is output. * If this unit detects a Dolby Digital or DTS signal, the Rename · Select "Auto" if you want this unit to automatically detect input signal types and select the appropriate input mode. · Select "DTS" if you want this unit to select DTS as the input mode. Multi CH Assign (Multi channel assignment) Use this feature to set the direction of the signals input into the center, subwoofer and surround channels when a source component is connected to the MULTI CH INPUT jacks. [. . . ] 531 to 1611 kHz · Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 µV/m 126 SPECIFICATIONS GENERAL · Power Supply [U. S. A. and Canada models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz [General and Asia model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]