User manual YAMAHA CBX-D5

[. . . ] Mark of the Unicorn® is a registered trademark of Mark of the Unicorn, Inc. All other trademarks are the property of their respective holders. NOTE: Although the system setups shown in the manual are valid at the time of printing, there is a possibility that future software upgrades may require different setups. [. . . ] · For more details about SCSI hard disks and connecting extra disks, see "Connecting Hard Disk Drives" on page 13 of the CBX-D5 Operating Manual. · In this system, only one external hard disk is used. It is, however, highly recommended, for the sake of data integrity, that you use at least two hard disks: one disk for your computer software and data such as Cubase Audio, MIDI song files, etc. , and the other disk purely for recording CBX-D5 sound files. 4 4 Chapter 3 : Cubase Audio & Atari TT TT System Chapter 3 : Cubase Audio & Atari System 3 Cubase Audio & Atari TT System An overview In this system the CBX-D5 is used with an Atari TT computer and the supporting software is Cubase Audio by Steinberg. What you will need 1) The CBX-D5, a power cable, two MIDI cables, a 50-way SCSI cable, and a SCSI terminator (all these except for one MIDI cable are provided with the CBX-D5). 2) An Atari TT computer and an Atari video monitor. 3) Steinberg's Cubase Audio software (Atari version). 4) A SCSI hard disk and a 25-pin D-SUB to 50-way SCSI cable. Making the connections 1) Connect the Atari computer's "MIDI OUT" connector to the CBX-D5's "MIDI IN" connector, and the computer's "MIDI IN" connector to the CBX-D5's "MIDI OUT" connector using the MIDI cables. 2) Connect the Atari computer's "SCSI" connector to the hard disk's SCSI connector using the 25-pin D-SUB to 50-way SCSI cable. 3) Connect the other hard disk SCSI connector to one of the CBX-D5's SCSI connectors using the 50-way SCSI cable. 4) Insert the CBX-D5's SCSI terminator into the CBX-D5's unused SCSI connector. 5) Connect the CBX-D5 to an AC receptacle using the supplied power cable. 6) Connect the Atari computer and its video monitor to an AC receptacle. NOTE: Clinch the SCSI connector's spring retaining clips and tighten the 25-pin D-SUB connector's locking screws for secure connections. Settings 1) Set the CBX-D5 to SCSI ID "5 or 6" using the thumb wheel switch on the rear of the CBX-D5. 2) Set the CBX-D5's "TO HOST" switch to "MIDI". 3) Set the hard disk to SCSI ID "1" (refer to its Operating Manual for details). NOTE: 1. External hard disks must be set with continuous SCSI IDs starting from 1 (1, 2, 3, 4. . . ). The TT's internal hard disk is set to ID 0. Do not set the ID number of the CBX-D5 so that it is consecutive to the ID number of the "HARD DISK". Switching on the the power 5 Switching on power 5 Figure 2. System connections HARD DISK POWER CABLE SCSI 50-WAY SCSI CABLE 25-pin DSUB to 50-WAY SCSI CABLE POWER CABLE SCSI TERMINATOR ATARI TT SCSI CBX-D5 MIDI OUT MIDI IN MIDI CABLES SCSI MIDI OUT MIDI IN POWER CABLE Switching on the power 1) Switch on the SCSI devices: CBX-D5, hard disk. 2) Switch on the Atari computer and load Cubase Audio. What to do next · The SCSI hard disk must be formatted before it can be used (refer to the hard disk's Operating Manual). See also "Working with Hard Disks" on page 18 of the CBX-D5 Operating Manual. [. . . ] See also "Working with Hard Disks" on page 18 of the CBX-D5 Operating Manual. · For recording and playback you should refer to the Digital Performer Operating Manuals. See also "Recording" on page 20 and "Playback" on page 23 of the CBX-D5 Operating Manual. Notes: · Other MIDI devices can be connected in this system as shown in "Mac" on page 31 of the CBX-D5 Operating Manual. [. . . ]