User manual YAMAHA CBXK3E

[. . . ] SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units. This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfortable. [. . . ] Continue command for sequencer/rhythm machine. Start command for sequencer/rhythm machine. Tempo entry for sequencer/rhythm machine. Setting this to 0 disables the MIDI clock transmission. When ASSIGNABLE Wheel is set to Tempo (cntrl. This allows selection of voice banks on the tone generator. The bank select message must include both MSB and LSB values. Stepping up or down through program numbers is also possible by holding down C and using the N / M buttons; see page 15. This resets the tone generator to General MIDI operation. WARNING: Be careful when using this, since it automatically changes whatever settings you've made on the tone generator. (Only GMcompatible tone generators respond to this message. ) This turns all sounds off over the current MIDI channel. However, this cannot be done with controller numbers 143 (Polyphonic Key Pressure), 147 (Velocity), or 148 (Tempo). When MSB and LSB values are entered, the LED display alternately flashes the MSB and LSB values. When no values have been entered, "- - -" appears in the LED display. *7 Transpose can be done in two ways: by repeatedly pressing the appropriate TRANSPOSE key or by entering the transpose value directly after pressing the appropriate TRANSPOSE key. To restore the normal transpose setting, hold C and press both G / H keys simultaneously. 31 Group B Functions -- List To select the Group B functions, hold down C and press K. Continue holding C while performing the operation steps for the desired Group B function. Key C2 Cm2 D2 Dm2 E2 For detailed explanations on the basic operations, refer to pages 25 and 28 ­ 29. The numbered footnotes that follow these charts provide additional details on certain operations. Panel Name STOP CONTINUE START TEMPO BANK SELECT Function Song Select Song Position Pointer Reset All Controllers -- Bulk Dump Out Operation Steps C + K Q [Value] L C + K W [MSB] [LSB] L C+KE -- Operation Examples (see page 28) -- C+KTL F2 Fm2 G2 Gm2 A2 PROGRAM CHANGE GM ON SOUND OFF XG ON MERGE ON/OFF -- C/M Mode On All Sound Off (all channels) TG300B Reset Local On/Off -- -- C+KUL C+KI C+KOL C+KP Am2 B2 MIDI CH FIXED VELOCITY Merge On/Off (each channel) *1 Touch Sensitivity *2 C + K { [Value] C + K } [Value] L C3 RPN Controller Direct Data Send (RPN) *3 C + K A [MSB] [LSB] L [Value] L C + K S [Value] L [Value] L C + K D [MSB] [LSB] L [Value] L C + K F [Value] L C+KG Cm3 CONTROLLER Controller Direct Data Send (controller numbers on panel) *3 D3 NRPN Controller Direct Data Send (NRPN) *3 Dm3 E3 DRUM NUMBER TRANSPOSE Q Device Number *4 Wheel Invert *5 F3 -- TRANSPOSE W MSB/LSB Invert *6 Single-Byte Data Send C+KH C + K [Value] L q Footnotes *1 Using system exclusive messages to turn Merge on or off can only be done for all channels (as in the corresponding Group A function). *2 When Fixed Velocity (in Group A) is set to a value other than 0, the Touch Sensitivity function is inactive. The following table shows the velocity range for the minimum, medium, and maximum Touch Sensitivity settings. Touch Sensitivity Value Velocity Range 1 (1) 32-127 (20-7F) 5 (5) 16-127 (10-7F) 10 (A) 1-127 (01-7F) *3 To send a specific value for the current control number assignment of the Wheel, hold down C, enter the desired value, and press L. However, this cannot be done with controller numbers 143 (Polyphonic Key Pressure), 147 (Velocity), or 148 (Tempo). 32 Group B Functions -- List * MIDI: MIDI OUT and TO HOST, Int. : Internal tone generator. Explanation Song Select command for sequencer/rhythm machine. Song Position Pointer for sequencer/rhythm machine. This resets all MIDI controller values to their reset values (minimum or center). [. . . ] A stereo EQ with adjustable LOW and HIGH. Cyclically modulates the center frequency of a wah filter. Bypass without applying an effect. * MSB, LSB is represented in hexadecimal. * LSB = 0 is the basic effect type. App-26 Effect Parameter List HALL1, 2, ROOM1, 2, 3 , STAGE1, 2, PLATE No. [. . . ]