User manual YAMAHA CC-70W

[. . . ] Natural Sound Mini Component System CC-70W/CC-70S Active Servo Technology CC-70W is composed of RX-S70, CDC-S90, KXW-S70 and NX-S70. CC-70S is composed of RX-S70, CDC-S90, KX-S90 and NX-S70. and Europe models, NX-S70 is optional in some areas. IMPORTANT!Please record the serial number of this unit in the space below. [. . . ] : If the winding direction is , when the tape reaches the end, playback automatically starts from the reverse side. If the winding direction is , the tape stops at the end. : When the tape reaches the end, playback automatically starts from the reverse side. Searching for the beginning of a desired selection TUNER DIRECT 1 1 6 6 A TIME 2 2 7 7 B PROG SEARCH SKIP DISC SKIP RANDOM REPEAT CD PRESET DOWN PLAY UP STOP PLAY TAPE REC/PAUSE DECK A/B POWER SLEEP DISPLAY VOLUME PHONO/AUX A/B/C/D/E TUNER 3 3 8 8 C TAPE 9 D EDIT STOP 0 E 4 4 5 5 Carry out the following operation during playback to find the beginning of a desired selection on the tape. To listen to the same selection Press the button if the direction of the current playback is . Press the button if the direction of the current playback is . To listen to the next selection Press the button if the direction of the current playback is . Press the button if the direction of the current playback is . * While searching, the corresponding play direction indicator flashes slowly. Notes · This function may not work for tapes with * Material with long pauses or quiet passages. * Low recording levels or excessive noise. * Pauses of less than 4 seconds between selections. · If searching is carried out at the first or the last part of a selection, the searching may not function correctly. +I0 PLAY/PAUSE - + 27 TAPE DECK OPERATION (for KXW-S70 Double Cassette Deck) 3 Tape Deck Continuous playback 1 2 Load the tapes into the DECK A and DECK B cassette compartments. Set the reverse mode switch to . The reverse mode switch can be operated before or during playback, and changes tape playback as follows: 1 24 4 1 <Tape A> Tape A Side A B Tape B Side A B Continuous play (8 times) <Tape A> Tape A Side B Tape B Side A B Tape A Side A Continuous play (8 times) TUNER DIRECT 1 1 6 6 A TIME 2 2 7 7 B PROG SEARCH SKIP DISC SKIP RANDOM REPEAT CD PRESET DOWN UP STOP PLAY TAPE REC/PAUSE DECK A/B POWER SLEEP DISPLAY VOLUME PHONO/AUX A/B/C/D/E TUNER 3 3 8 8 C TAPE 9 D EDIT STOP 0 E 4 4 5 5 3 4 3 4 +I0 PLAY/PAUSE Press the DECK A or B select button to select the tape to be played back first. Press the play button to listen to side A, or the play button for side B. 4 PLAY - + Dolby B and C Type Noise Reduction With cassette tapes, the most noticeable form of noise is high frequency hiss. To reduce this hiss noise, this unit has been equipped with a newly developed Dolby C noise reduction system in addition to its conventional Dolby B NR. Either type of noise reduction may be selected with the switch provided. Dolby B NR has a noise reduction effect of about 10 dB in the high frequency range. The corresponding figure with Dolby C NR is about 20 dB, but this is over the entire range where the human ear is most sensitive to noise (2 kHz to 8 kHz). Also, Dolby C NR has the same noise reduction effect at both high and low signal levels. In addition, Dolby C NR improves the tape's MOL (Maximum Output Level). Dolby noise reduction is a 2 part process that acts both on recording and playback; be sure that the noise reduction button is set to the same position on record and play. * Noise in the source material cannot be reduced with the Dolby NR system. · DOLBY B. C NR Dolby and the double D mark are trademarks of Dolby Laboratories Licensing Corp. [. . . ] Head is dirty. Sound is distorted or fades out. Head is dirty. Tape is worn. TAPE DECK Poor sound quality. Excessive noise. Dolby NR switch is set to wrong position. Tape is worn. Tape travel stops in middle of playback or recording. Slack tape coming out of cassette shell. [. . . ]