User manual YAMAHA CD-400

[. . . ] 8 RANDOM-SEQUENCE PLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 PROGRAM PLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 REPEAT PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 INDEX SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If, during this play, you find a disc that you want to listen to, press the DISC SCAN button once again or press the PLAY button to cancel this function. The unit will enter into the normal play mode. Notes During this play, the disc tray numbers blink in the display. Every time the play of a disc is finished, the corresponding tray number is changed from flashing to lighting. DISC SCAN q q If the disc being played has a long blank space between tracks, you will hear no sound during disc scan. Selecting time displays and the text data You can select any of the four time displays by pressing the TEXT/TIME display mode-select button. When you play a CD with CD TEXT, the disc title, artist name, and track name are also displayed. Each time you press the TEXT/TIME display mode-select button, the display changes as follows. Elapsed time of the track now playing 5DISCS 2345 6 7 8 9 10 11 12 Track name Remaining time of the track now playing 5DISCS 2345 6 7 8 9 10 11 12 Artist name TEXT/ TIME Total disc play time 5DISCS 2345 6 7 8 9 10 11 12 Disc title Total remaining time on the disc 5DISCS 2345 6 7 8 9 10 11 12 :when playing back a disc without CD TEXT :when playing back a CD TEXT disc Notes q The remaining time will not be displayed if the track number is 21 or higher. q The disc title, artist names, or track names may not be displayed with some CD TEXT discs. In this case, "(NO ENTRY)" appears in the display. 11 Changing brightness of the display If desired, you can change brightness of the display in three degrees by pressing the DIMMER button. DIMMER Normal illumination Slightly dim Dim CD-400 only Adjusting the level of signals output into an amplifier, etc. You can adjust the level of sound signals output from the LINE OUT terminals on the rear panel into an amplifier, etc. as you prefer by using the OUTPUT LEVEL buttons. CD-400 only When you listen with headphones Connect the headphones to the PHONES jack and adjust the volume by using the OUTPUT LEVEL buttons. * Note that the use of the OUTPUT LEVEL buttons will also vary the level of the signal output to an amplifier, etc. PHONES ­ OUTPUT LEVEL + or OUTPUT LEVEL ­ + (On the front panel) For optimum sound quality * When the DIGITAL AUDIO OUT (OPTICAL) terminal is used for the connection, set the level of output signals to max. * The level of output signals can be checked in the display. 12 English RANDOM-SEQUENCE PLAY You can play the tracks in a random sequence (up to 99 tracks). Play will begin from the beginning of the program. To check program data 1. During program play, press the STOP button. Each time the SKIP button is pressed, the track numbers and sequential order of the programmed tracks can be checked one after another. The display of the track number can be returned (sequentially in reverse order) by pressing the SKIP button. To cancel a programmed sequence There are several methods, as described below. q Press the STOP button or the CLEAR button while the unit is stopped. q Switch off the power. To correct program data 1. Follow the procedure described in "To check program data". Display the track number to be corrected by pressing the SKIP button. Press a numeric button to select a track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed. After the correction has been completed, press the PROG button or PLAY button once again. 15 REPEAT PLAY You can play any desired track or disc (or a set of discs) repeatedly by pressing the REPEAT button. [. . . ] Check the disc carefully; replace it if necessary. Check the disc carefully; replace it if necessary. If the problem persists, the cables may be defective. Set the amplifier controls to the correct input selection. [. . . ]