User manual YAMAHA CD-X1

[. . . ] 8 Random-Sequence Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · If the power is switched off during the random-sequence play, pressing the POWER switch again to turn the unit on will automatically restore the random-sequence play. This feature is useful for timer play. or REPEAT PLAY You can play any desired track or the entire disc repeatedly by pressing the REPEAT button. The repeat play mode will change whenever you press the REPEAT button. SINGLE REPEAT A single track is repeatedly played. * This is also available in the programmed-play mode and the random-sequence play mode. * If the repeat play mode is switched off, the programmed-play mode or the random-sequence play mode will be resumed. FULL REPEAT All tracks (the entire disc) are played repeatedly. * In the programmed-play mode, all programmed tracks are repeatedly played. * In the random-sequence play mode, all randomly sequenced tracks are repeatedly played in the same order. * If the power is switched off during FULL REPEAT play mode, pressing the POWER switch again to turn the unit on will automatically restore FULL REPEAT play. (Off) REPEAT SINGLE REPEAT FULL REPEAT 12 English PROGRAM PLAY By programming tracks, you can enjoy listening to your favorite tracks in any desired order. As many as 40 tracks can be programmed in sequence. SYNCHRO DIMMER TIME OPEN/ CLOSE SPACE 1 PEAK 2 TAPE 3 CLEAR PROG INDEX 2 3 1 1 Stop the unit. STOP 4 5 6 +I0 0 7 8 9 REPEAT RANDOM SEARCH ­ OUTPUT LEVEL + PAUSE SKIP STOP PLAY 4 3 Program a desired track by pressing the corresponding number button. 6 2 PROG PROGRAM * Repeat this operation to program more tracks. The index system is a method for sub-dividing tracks into smaller divisions (for example, the movements within classical symphonies) for easier location of those parts. The liner notes with the disc usually tell if such index numbers are included. · If an index number is selected that is higher than any index number on that disc, play will start from the last index number point on the disc. · For some discs, play may begin slightly prior to the actual designated index point. · If the disc has no encoded index points, play will begin from the start of the selected track. · The index number can be designated only while "INDEX" appears on the display. 2 INDEX INDEX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3 Select the desired index number. 6 14 English TRACK PROGRAMMING FOR RECORDING TO TAPE The unit can automatically program tracks considering the tape's total time. This convenient feature can help you to program tracks so that they fit onto the tape with the least amount of unrecorded space remaining at the end of each side (A and B) of the tape. L Automatic tape-programming The unit can automatically program tracks on a disc in their original order. 4 Otherwise, you can enter the tape's total possible recording time manually. Example: For a C-64 tape (32 minutes on each side) 6 4 3 SYNCHRO DIMMER TIME OPEN/ CLOSE 2 5 SPACE 1 PEAK 2 TAPE 3 CLEAR PROG + INDEX 4 5 6 +I0 0 7 8 9 REPEAT RANDOM SEARCH ­ OUTPUT LEVEL + PAUSE SKIP 1 1 Stop the unit. STOP PLAY 4 7 6, 7 5 Press the REPEAT button. REPEAT The unit automatically programs tracks for side A and side B separately considering the tape's total time. STOP 6 Begin recording on the tape deck and press the PLAY button on this unit at the same time. 7 The unit will pause at the end of side A of the tape. * The peak level searching function of this unit is useful for adjusting the recording level on the tape deck. (Refer to page 18. ) Turn the tape over to side B, resume recording and, at the same time, press the PLAY or PAUSE button on this unit. Notes · All the tracks may not be programmed if the tape's length is not enough. To program all tracks, use a longer tape. [. . . ] Play does not begin. Improper amplifier operation. Sound "skips. " The player is being subjected to vibrations or impacts. Sound "hums. " Improper cable connections. Noise from a nearby tuner. The remote control transmitter does not work. The tuner is too close to the player. [. . . ]