User manual YAMAHA CD-R400TX

[. . . ] CDR400tx User Guide Guide de I'utilisateur Bedienungsanleitung R POWE ON/ DISC Recorda ble / READ WRITE x 400t CDR- VOL COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CDR400tx This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] To remove stubborn dirt or grease from the recording surface use only nonabrasive foam-tipped swabs (such as Chemtronics Foamtips #120) with a small amount of pure, denatured alcohol. To avoid scratching the recording surface BE SURE TO USE ONLY LIGHT STROKES, beginning at the disc center, pulling directly towards the disc's outer edge. Always record in a dust-free environment. If the disc must be removed from CDR400tx before recording is finished, store the disc in a clean, dust-free environment. If a disc tray accumulates dust, DO NOT USE IT FOR DISC RECORDING. Always use a clean, dust-free tray for disc recording. · · · · If CDR400tx is vibrated while recording, the recording may fail. To avoid such failures observe the following practices: · Place CDR400tx on a solid, stable surface, away from high-traffic areas. The surface must allow CDR400tx to operate in a level, horizontal position. Avoid touching or handling CDR400tx when recording. · Note: Once the disc has been finalized (and no more recording is possible), it can be handled with the same care that any CD should be handled. iv Table of Contents Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CDR400tx Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Orange Book Compatible Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 1 - System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 For an IBM-PC computer with DOS or Windows . . . . . . . . 4 For a Macintosh computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 2 - Touring Around CDR400tx . . . . . . . . . . . . . . . . . . . 6 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 3 - Installing the Yamaha CDR400tx Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CDR400tx drive settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Caution: If you are using other SCSI devices, be sure to use a unique ID number for each device. Be sure to turn off the power to the drive before you set the SCSI ID number. Note: When you are using Windows 95, and if the SCSI ID setting on the rear panel is the same as the number assigned to another SCSI device, the Plug and Play component of Windows 95 will automatically assign an unused number to the CDR400tx (SCAM protocol level 1). CDR ­ ID Pressing this switch repeatedly will decrease the SCSI ID number by one each SCSI ID Number Pressing this switch repeatedly will increase the SCSI ID number by one each time. 1 + o Terminator setting The terminator setting indicates whether or not this device is the last connected SCSI device. Terminator ON TERMINATOR -- Use this setting if the CDR400tx is the last device in the SCSI daisy-chain. OFF ON Terminator OFF TERMINATOR -- Use this setting if devices other than the CDR400tx are in the SCSI daisy-chain and the CDR400tx is not the OFF ON last device. 8 Chapter 3 - Installing the Yamaha CDR400tx Drive Cable Connection Power cable Insert the power cable securely to the "AC IN" connector on the rear panel. SCSI-1 SCSI-2 CDR ID 1 TERMINATOR LINE OUT R L OFF ON SCSI cable Connect the SCSI cable to either of the CDR400tx rear panel SCSI connectors (1) or (2), and connect the other end of the SCSI cable to the host computer. [. . . ]