User manual YAMAHA CDX-5000

[. . . ] 10 Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Track Programming for Recording to Tape . . . . . . . . . . . . . . . . . 12 Notes about the Remote Control Transmitter . . . . . . . . . . . . . . . . . 16 Notes about Handling Compact Discs . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Normal illumination MODE Slightly dim Dim When you listen with headphones Connect the headphones to the PHONES jack and adjust the volume by using the OUTPUT LEVEL buttons. and ) button can be used during playing, · The SKIP ( but only within the range of the programmed tracks. and ) button can be used during · The SEARCH ( playing to search through all tracks, including unprogrammed tracks. · The PAUSE mode can also be programmed (one time only), if so desired, by pressing the PAUSE button instead of a numeric button. (In this case, " B" is illuminated in the display. ) · If, for a compact disc with 25 tracks or more, track number 25 or higher is programmed, the total time will disappear from the display. Shows the program number for the track to be set next. Shows the total time of the tracks currently programmed. Shows only the numbers of programmed tracks. * If "P-01" does not appear in the display after the PROG button is pressed, press the TIME display mode-select button. * If the total time exceeds 99 minutes and 59 seconds, the time will not be displayed. 10 To stop program play Press the STOP button. The first track number programmed will be displayed. Play will begin from the beginning of the program. To cancel a programmed setting There are several methods, as described below. Notes · All tracks may not be programmed if the tape's length is not enough. To program all tracks, use a longer tape. · In step 4, you can check the program data for side A and sideB. 2 Enter the tape's total possible recording time. TAPE You can select any of four tape lengths by pressing the TAPE button. TAPE (off) 1 2 3 3 Otherwise, time manually. enter the tape's total possible you can also recording Example: For a C-64 tape (32 minutes on each side) + 10 1 2 3 4 5 6 7 8 9 0 4 1 2 Shows the number of programmed tracks. Shows the total time of programmed tracks. Shows the programmed track numbers. 12 Manual tape-programming This is for recording desired tracks in any desired order onto a tape. 2 LOGODISK 6, 7 4, 7 3, 5 1 2 PROG Follow steps 1 ­ 3 on page 12. 5 Select the track numbers (to be recorded on side B) in the desired order. + 10 1 2 3 4 5 6 7 8 9 0 6 Begin recording onatthe tape deck and press the PLAY button on this unit the same time. 3 Select the track numbers (to be recorded on side A) in the desired order. + 10 1 2 3 4 5 6 7 8 9 0 7 The unit will pause to sideend ResumeArecording and, at the of side of the tape. Turn the tape over B. at the same time, press the PLAY button or the PAUSE button on this unit. Notes · If, in step 3 or 5, "E : rr" appears in the display, the track number just selected cannot be programmed because there is not enough time remaining on the tape. However, at this time, if any other track number is flashing continuously in the display, you can program it instead of the unprogrammable one. · In step 3 or 5, each time a selection is made, the track number and the tape's remaining time will be displayed, and then the display will change to indicate the number of the next program. * Programmed track numbers are illuminated on the display. You can select a track which can be programmed for the remaining time of (the side of) the tape from track numbers flashing on the display, but you cannot select any darkened track number. 4 Program the pause mode. PAUSE Notes on tape programming · To check, cancel or correct program data, refer to page 11. [. . . ] Set the amplifier controls to the correct input selection. If the problem persists, the cables may be defective. Move the tuner and player farther apart. Change position of the main unit. Sound "hums". [. . . ]