User manual YAMAHA CDX-700U

[. . . ] 5 Identification of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Random-Sequence Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This is convenient for locating a precise position within a track, or for reviewing the contents quickly. Manual search can also be performed while disc play is paused, though no sound will be heard. When using the SKIP/SEARCH buttons on the front panel: Be careful not to release the button just after it is pressed, otherwise the play is skipped to the beginning of the next track or returned to the beginning of the current track. (Press and hold. ) 10 English Scanning discs to search for a desired disc (or to check discs on the disc tray) When the DISC SCAN button is pressed when this unit is stopped, this unit will play an initial part of each disc in turn. If, during this play, you find a disc that you want to listen to, press the DISC SCAN button once again or press the PLAY button to cancel this function. The unit will enter into the normal play mode. Notes During this play, the disc tray numbers flash on and off on the display. Every time the play of a disc is finished, the corresponding tray number is changed from flashing to lighting. DISC SCAN q q There might be cases that you will hear no sound during disc scan. An example of this would be if the disc being played has a long blank space between tracks. Selecting time displays You can select any of the four time displays by pressing the TIME display mode-select button. Elapsed time of the track now playing 5DISC Total remaining time on the disc 5DISC TOTAL REMAIN 2 3 4 5 6 7 8 9 10 1 1 12 2 3 4 5 6 7 8 9 10 1 1 12 TIME Remaining time of the track now playing 5DISC REMAIN 2 3 4 5 6 7 8 9 10 1 1 12 Total disc play time 5DISC TOTAL 2 3 4 5 6 7 8 9 10 1 1 12 Note The remaining time will not be displayed if the track number is 21 or higher. 11 Changing brightness of the display If desired, you can change brightness of the display in three degrees by pressing the DIMMER button. DIMMER Normal illumination Slightly dim Dim CDC-902 only Adjusting the level of signals output into an amplifier, etc. You can adjust the level of sound signals output from the LINE OUT terminals on the rear panel into an amplifier, etc. as you prefer by using the OUTPUT LEVEL button. CDC-902 only When you listen with headphones Connect the headphones to the PHONES jack and adjust the volume by using the OUTPUT LEVEL button. * Note that the use of the OUTPUT LEVEL button will also vary the level of the signal output to an amplifier, etc. ­ OUTPUT LEVEL + OUTPUT LEVEL or ­ + PHONES (On the front panel) * When the DIGITAL AUDIO OUT (OPTICAL) terminal is used for the connection, set the level of output signals to max. * The level of output signals can be checked on the display. 12 English RANDOM-SEQUENCE PLAY You can play the tracks in a random sequence (up to 99 tracks). The display of the track number can be returned (sequentially in reverse order) by pressing the SKIP button. To cancel a programmed sequence There are several methods, as described below. q Press the STOP button or the CLEAR button while the unit is stopped. q Switch off the power. To correct program data 1. Follow the procedure described in "To check program data". Display the track number to be corrected by pressing the SKIP button. Press a numeric button to select a track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed. After the correction has been completed, press the PROG button or PLAY button once again. 15 REPEAT PLAY You can play any desired track or disc (or a set of discs) repeatedly by pressing the REPEAT button. The repeat play mode will change whenever you press the REPEAT button. SINGLE REPEAT (REP S) (OFF) A single track is repeatedly played. * This is also available in the program play mode and the random-sequence play mode. (If the repeat play mode is switched off, the program play mode or the randomsequence play mode will be resumed. ) REPEAT REP S FULL REPEAT (REP F) In the "1DISC" disc play mode: A designated disc is played repeatedly played. [. . . ] Wait 20 to 30 minutes after switching the unit ON before trying to play a disc. Check the disc carefully; replace it if necessary. If the problem persists, the cables may be defective. Set the amplifier controls to the correct input selection. [. . . ]