User manual YAMAHA CE-20

[. . . ] Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] Press jCursor k / n to select the desired menu then press jENTER. Items of the selected menu are displayed. Example (Function Setup) Function Setup Speaker Setup You can set various items for speakers. One is "Auto Setup" (YPAO) for automatic adjustment and another is "Manual Setup" for manual adjustment. y · The default settings are marked with "*". ADVANCED OPERATION 3 Auto Setup ADDITIONAL INFORMATION HDMI Display Volume Input Rename Zone Network Rhapsody Information Automatically adjusts output characteristics of speakers to obtain optimum balance for the output sound based on positions and performances of the speakers and acoustic characteristics or the room, which are automatically measured. For details on operations, see page 21. y · To return to the previous menu, press jRETURN. Manual Setup Adjusts output characteristics of speakers based on manually set parameters. After "Auto Setup" (YPAO) is performed, you can check automatically adjusted parameters in the "Manual Setup" menu. Fine adjust the parameters for your preference if necessary. Speaker Configuration Sets speaker configurations, such as connection status of speaker and a size of the connected speaker (sound reproduction capacity), suitable for the listening environment. y · The speaker configuration includes items for defining a speaker size: "Large" or "Small". "Large" and "Small" refer to speakers with woofer diameters 16 cm or larger and smaller than 16 cm, respectively. 4 If necessary, press jCursor k / n to select the desired submenu then press jENTER. Outputs low-frequency components of the front left and right channels. None [4] Large x 1 Small x 1 Large x 2 Small x 2 Front Speaker Choices: Small, Large* Sets the sizes of front left and right speakers. Small Select this when small speakers are connected. Low-frequency components of the front left and right channels are output from a subwoofer. Select this when no surround back speaker are connected. Surround back channel signals are output from the surround L/R speakers and subwoofer. If the subwoofer is disabled, they are output from the surround L/R speakers and front speakers. Select this when one large surround back speaker is connected. Select this when one small surround back speaker is connected. Select this when two large surround back speakers are connected. Select this when two small surround back speakers are connected. 60 En Operating various settings for this unit (Setup menu) y · When "Surround Back Speaker" is set to "None", "PLIIx Movie", "PLIIx Music" and "PLIIx Game" of the surround decode mode (page 29) are not available. FR. L / FR. R / CNTR / SUR. L / SUR. R / SBL / SBR / SWFR / PR. L / PR. R Adjustable range: 0. 30m to 24. 00m (1. 0ft to 80. 0ft) Defaults: 3. 00m (10. 0ft) (FR. L, FR. R, SWFR, PR. L, PR. R) 2. 60m (8. 5ft) (CNTR) 2. 40m (8. 0ft) (SUR. L, SUR. R, SBL, SBR) Bass Crossover Frequency Choices: 40Hz, 60Hz, 80Hz*, 90Hz, 100Hz, 110Hz, 120Hz, 160Hz, 200Hz INTRODUCTION Sets the lower limit of the low-frequency component output from a speaker with a size set to "Small" (Small x 1, Small x 2) Sound with a frequency below that limit is output from a subwoofer or front speakers. If your subwoofer has a volume control or a crossover frequency control, set the volume to half or the crossover frequency at the maximum. Subwoofer Phase Choices: Normal*, Reverse y · Available items differ depending on the "Speaker Configuration" settings (page 59). [. . . ] This package is an SSL implementation written by Eric Young (eay@cryptsoft. com). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc. , code; not just the SSL code. [. . . ]