User manual YAMAHA CL3

[. . . ] Owner's Manual Keep This Manual For Future Reference. EN Contents PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About utility software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About firmware updates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About the Owner's Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Conventions in this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Setting the date and time of the internal clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Word clock connections and settings . . . . . . . . . . . . . . . 36 Making HA (Head Amp) analog gain settings . . . 37 Sending an input channel signal to the STEREO bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Quick Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] "CUSTOM" Bank Select keys enable you to assign and recall a bank with your own assortment of the channels or DCA groups. These banks are called "custom fader banks. " Since the custom fader banks enable you to assign a combination of different types of channels, you can control different types of channels as a group. These controls affect DCA groups 1­8. 2. Use the controls of the Channel Strip section. Use the channel knob to adjust a parameter selected by the [GAIN/PAN/ASSIGN] key. Each channel's display indicates the currently-assigned channel information. For the channel display information, access SETUPUSER SETUPPREFERENCE, then set NAME DISPLAY to NAME ONLY or FULL FUNCTION. 3. To release the channels or DCA groups that were retained for the Centralogic section, press the Bank Select key you operated in step 1 once again, and hold it down until the Bank Select key LED changes from blinking to lit. When the Bank Select key LED changes to being lit, its channels or DCA groups will be assigned to both the Centralogic section and the OVERVIEW screen. Custom fader bank settings Follow the procedure below to set up a custom fader bank for control on the Channel Strip section. 1. Press the SETUP button located in the function access area in the display. 2. Press the USER SETUP button in the upper left of the SETUP screen. 3. Press the CUSTOM FADER tab near the bottom of the USER SETUP screen. The CUSTOM FADER BANK / MASTER FADER screen will appear. Owner's Manual 29 Basic operation of the CL series 4. Select a target custom fader bank. Channel strips are categorized into four blocks; from your left, block A, block B (Centralogic section), block C (only for CL5), and Master. MIX1­16 and MIX17­24/MATRIX, and the buttons that enable you to select the destination MIX/MATRIX buses. 1 ON FADER switch button Pressing this button repeatedly will switch between MIX1­16 and MIX17­24/MATRIX. 2 MIX/MATRIX bus select buttons These buttons enable you to select the destination MIX/MATRIX buses. Two buses that are paired in stereo are represented by one button. 5. Press the number in the FADER area, then press the [SEL] key for the channel that you want to assign to that fader. 2. Press the ON FADER switch button repeatedly to select MIX1­16 or MIX17­24/MATRIX. In this way, you can use the MIX/MATRIX bus select buttons to specify the destination MIX/MATRIX buses. 3. Use the MIX or MATRIX bus select buttons in the function access area to select the send-destination MIX/MATRIX bus. You can also select a channel in the display. Press the button below the desired number to display the CH SELECT screen. First select the tab for a channel group, then select individual channels. To return to the previous screen, press the CLOSE button. NOTE · Alternatively, press a SEND LEVEL knob in the SELECTED CHANNEL section to display a popup window, from which you can select a MIX/MATRIX bus. · You can also select a MIX/MATRIX bus by using the Bank Select keys and the [SEL] keys in the Centralogic section. [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 MALTA Olimpus Music Ltd. Louis Street Msida MSD06 Tel: 02133-2144 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]