User manual YAMAHA CLP-511E

[. . . ] SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. [. . . ] Press the [­/NO] and [+/YES] buttons simultaneously to recall the default setting (different for each voice combination). F4. 5: Right Voice Effect Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F4. 6: Left Voice Effect Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . These functions make it possible to individually set the depth of the chorus effect for the left-hand and right-hand split-mode voices. Use the [­/NO] and [+/YES] buttons to set the effect depth for the corresponding voice as required. A setting of "0" produces no effect, while a setting of "20" produces maximum effect depth. Press the [­/NO] and [+/YES] buttons simultaneously to recall the default setting (the default effect depth setting is different for each voice). NOTE · The effect depth settings cannot be changed unless the EFFECT is ON. The Function mode must be exited before EFFECT can be turned ON. F4. 7: Damper Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Damper Mode function determines whether the damper pedal affects the right voice, the left voice, or both the left and right voices in the split mode. Use the [­/NO] and [+/YES] buttons to select "2" for the left voice, "1" for the right voice, or "ALL" for both voices. Press the [­/NO] and [+/YES] buttons simultaneously to recall the default setting: "ALL". F4. 8: Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . This function resets all split-mode functions to their default values. Press the [+/YES] button to reset the values. "End" will appear on the display when all functions have been reset. 24 The Function Mode F4 CLP-411 Metronome Functions F5 CLP-511 Metronome Functions After selecting "F4. Y" or "F5. Y", press the [+/YES] button to engage the metronome function sub-mode, then use the [<] and [>] buttons to select the desired metronome function, as listed below. s SHORTCUT: You can jump directly to the metronome functions by pressing the [FUNCTION] button while holding the [METRONOME] button. F4. 1/F5. 1: Beat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use this function to set the time signature of the metronome as required (i. e. the number of unaccented beats that occur between each accented beat). Use the [­/NO] and [+/YES] buttons to set the time signature to "0" (no accent), or a value between "2" and "6", as required. Press the [­/NO] and [+/YES] buttons simultaneously to recall the default setting: "0". F4. 2/F5. 2: Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use the [­/NO] and [+/YES] buttons to set the metronome volume as required. A setting of "1" produces minimum sound, while a setting of "20" produces maximum metronome volume. Press the [­/NO] and [+/YES] buttons simultaneously to recall the default setting: "10". F5 CLP-411 Left Pedal Mode F6 CLP-511 Left Pedal Mode This function sets the left pedal for normal soft-pedal operation, or for song start/stop operation. Use the [­/NO] and [+/YES] buttons to select the desired left-pedal mode. "1" is the normal soft-pedal mode, and "2" is the start/stop mode. When the start/stop mode is selected, the left-pedal functions in the same way as the panel [START/STOP] button. F7 (CLP-511) Piano Song Part Cancel Volume This functions sets the volume at which a "canceled" part is played during piano song playback on the CLP-511 (see page 9 for information on the "part-cancel" function). Use the [­/NO] and [+/YES] buttons to set the volume as required. A setting of "0" produces no sound, while a setting of "20" produces maximum volume. Press the [­/NO] and [+/YES] buttons simultaneously to recall the default setting: "5". 25 The Function Mode F6 CLP-411 MIDI Functions F8 CLP-511 MIDI Functions q A Brief Introduction to MIDI MIDI, the Musical Instrument Digital Interface, is a worldstandard communication interface that allows MIDI-compatible MIDI OUT MIDI IN musical instruments and equipment to share musical information and control one another. This makes it possible to create "systems" of DOU-10 MIDI instruments and equipment that offer far greater versatility and control than is available with isolated instruments. [. . . ] IMPORTANT: The louder the sound, the shorter the time period before damage occurs. Temperature considerations: Electronic products should be installed in locations that do not significantly contribute to their operating temperature. Placement of this product close to heat sources such as; radiators, heat registers and other devices that produce heat should be avoided. 7. Some Yamaha products may have benches and/or accessory mounting fixtures that are either supplied as a part of the product or as optional accessories. Some of these items are designed to be dealer assembled or installed Please make sure that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by Yamaha are designed for seating only. [. . . ]