User manual YAMAHA CLP-760

[. . . ] To change the setting use a "minus" screwdriver to rotate the selector dial so that the correct voltage appears next to the pointer on the panel. WICHTIG Überprüfung der Stromversorgung Vergewissern Sie sich vor dem Anschließen an das Stromnetz, daß die örtliche Netzspannung den Betriebsspannungswerten auf dem Typenschild an der Unterseite des Instruments entspricht. In bestimmten Verkaufsgebieten ist das Instrument mit einem Spannungswähler an der Unterseite neben der Netzkabeldurchführung ausgestattet. Falls vorhanden, muß der Spannungswähler auf die örtliche Netzspannung eingestellt werden. Der Spannungswähler wurde werkseitig auf 240 V voreingestellt. [. . . ] (Each voice is associated with a unique program-change number. ) Similarly, if the Clavinova is playing MIDI data received from an external device, then receipt of a Program Change message will cause the Clavinova to change the voice used to reproduce this data. (Note that this change applies only to the MIDI data; the voice produced by the Clavinova keyboard does not change. ) There are times when you may want to disable the use of Program Change messages, so that voice switching at both sides must be handled locally. You can do this by setting the PrgChg value to OFF. In this case, the Clavinova will not generate messages when voice selectors are pressed, and will not respond to any Program Change messages that it receives. · Program-change numbers on the CLP-760/611 Program-change number assignments on the CLP-760/611 are in conformance with the XG standard. Refer to "MIDI Data Format" (page 48) for specific information. 13. 5 CtrlChg (Control Change enable/disable) Values: ON, OFF Default: ON Control Change messages transfer performance-related control information from one MIDI device to another. Such information includes pedal actions and volume settings. If you are using the Clavinova to control an external device, for example, then each time you step on the damper pedal a corresponding Control Change message is issued to that device. If you are using an external device to control the Clavinova, then Control Change messages received from that device will cause appropriate changes at the Clavinova side. These changes apply only to incoming MIDI data; panel settings and keyboard sound do not change. (But note that reverb-depth control change is an exception, since it affects both MIDI and local sound. ) There are times when you may want to disable the use of Control Change messages. · When transmitting bulk data, the Clavinava will not transmit other types of MIDI data and will not recognize incoming MIDI messages. BRILLIANCE REVERB EFFECT TOUCH 2 Next, press [+/YES] to enter the subfunction group. Then use [t], [s] to move among the different subfunctions, and [-/NO], [+/YES] to set the values. (On CLP-760 only:) F14. MicRevDpt (Microphone reverb depth) This function sets the reverb depth (intensity of reverb effect) applied to microphone input. (Note that this function is not available on the CLP-611. ) 1 To access this setting, enter FUNCTION mode and go to main function F14. Subfunctions 14. 1/15. 1 Voice (Voice settings) 14. 2/15. 2 MIDI (MIDI settings) 14. 3/15. 3 Tune (Tuning and temperament settings) 14. 4/15. 4 Pedal (Pedal settings) 14. 5/15. 5 Display (Display mode) Values: ON, OFF Default: OFF* * But note that the Backup ON/OFF settings themselves, as well as recorded performance data, are always backed up. 1 2 NORMAL ROOM MEDIUM TEMPO BRILLIANCE REVERB EFFECT TOUCH 2 Press [-/NO] or [+/YES] to change the setting. Values: 0, . . . , 20 Default: 10 36 CLP-760/611 Configuration Functions (FUNCTION mode) Parameters in Each Group 14. 1/15. 1 Voice (Voice settings) · · · · · · · · · · · · · Voice selection DUAL mode ON/OFF status and voice combination The [F4. DualFunc. ] settings (for each voice combination) SPLIT mode ON/OFF status and voice combination The [F5. SplitFunc. ] settings (for each voice combination) REVERB type and depth EFFECT type and depth (for each voice) BRILLIANCE setting VARIATION ON/OFF status (for each voice) TOUCH setting All [F6. OrganEdit] settings All [F7. Metronome] settings The [F14. MicRevDpt] setting (CLP-760 only) 14. 2/15. 2 MIDI (MIDI settings) All MIDI settings ([F13. MIDIFunc. ] settings 13-1 to 13-6) 14. 3/15. 3 Tune (Tuning and temperament settings) · · · · Current TRANSPOSE setting Keyboard fine tuning ([F1. Tune] setting) Key-by-key fine tuning ([F2. KTune] settings) Temperament selection ([F3. Scale] settings) 14. 4/15. 4 Pedal (Pedal settings) · Left-pedal function ([F9. L. Pedal] setting) · Damper-pedal depth ([F10. DamperDpt] setting) · Number of damper-pedal levels ([F11. Damper] setting) 14. 5/15. 5 Display (Display mode) Display mode ([F8. Display] setting) · To reset all values to their factory defaults. . . Switch the power OFF, then hold down the highest key on the keyboard (key C7) and switch the power back on. Note that this operation will also delete all recorded performance data. For a listing of the factory default values, see page 47. CLP-760/611 Configuration Functions (FUNCTION mode) 37 The Clavinova's Device Connectors MASTER VOLUME PIANO 1 PIANO 2 CLAVI. TONE E. PIANO 1 E. PIANO 2 HARPSICHORD METRONOME SONG MEASURE TEMPO RECORDER FUNCTION TRANSPOSE SPLIT VARIATION TRANSPOSE SPLIT MAX DEMO/ PIANO SONG 1/ R 2/ L BRILLIANCE REVERB MIN EFFECT TOUCH VIBES STRINGS CHOIR PIPE ORGAN ORGAN COMBINATION BASS MELLOW ROOM CHORUS HARD NORMAL HALL 1 SYMPHONIC MEDIUM BRIGHT HALL 2 TREMOLO SOFT STAGE FIXED ECHO BRILLIANCE REVERB EFFECT TOUCH TEMPO SONG SELECT START/ STOP REC ­ / NO +/ YES STEREO SAMPLING CLP-911 POWER (CLP-760) PHONES 3 MIC. VOL. MIN MAX MIC. PHONES 12 CLP-611 CLP-760 3 1 MIC. jack (CLP-760) Connecting a microphone to the MIC jack (a standard phone jack) lets you sing along. The input from the microphone is mixed with the keyboard sound and produced at the Clavinova's speakers. dial Use the dial to adjust the input volume from the microphone. NOTE Microphone reverb depth. . . Although the reverb type setting is always the same for both keyboard and microphone, the CLP-760 allows you to set an independent reverb depth for the microphone input. [. . . ] If you should move, or if any doubt exists about the supply voltage in your area, please contact your dealer for supply voltage verification and (if applicable) instructions. The required supply voltage is printed on the name plate. For name plate location, please refer to the graphic found in the Special Message Section of this manual. 2. This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by the manufacturer. If a cart, rack, or stand is used, please observe all safety markings and instructions that accompany the accessory product. 9. The power supply cord (plug) should be disconnected from the outlet when electronic products are to be left unused for extended periods of time. [. . . ]