User manual YAMAHA CP-70B

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] Connect / Disconnect Input source: BLUETOOTH (DOCK) PREPARATION Connects to or disconnects from a Bluetooth component. Pairing Input source: BLUETOOTH (DOCK) 1 Performs pairing of this unit and a Bluetooth component (page 44). Video Out Input source: MULTI CH Choices: AV1 to AV6, V-AUX, Off* Rotate the RINPUT selector (or press dMULTI) to select "MULTI CH" as the input source. The Option menu for "MULTI CH" is displayed. Press jCursor k / n to select "Video Out" and then press jENTER. 2 3 BASIC OPERATION Specifies a video signal to be output during a multichannel audio reproduction. For details, see "Selecting a video signal to be output during a multi-channel audio reproduction" on this page. Video;;;;;;Off ADVANCED OPERATION 4 Press jCursor l / h to select a video input jack to be used during a multi-channel audio reproduction. ­AV1-2 (COMPONENT VIDEO) ­AV3-6 (VIDEO) ­V-AUX (VIDEO) ­Off (no video output) To exit the Option menu, press rOPTION. ADDITIONAL INFORMATION 5 APPENDIX English 49 En Editing surround decoders/sound field programs Setting sound field parameters Although the field sound programs would satisfy you as they are with the default parameters, you can arrange sound effect or decoders suitable for acoustical conditions of sources or rooms by setting the parameters. y · You cannot configure the parameters when "Memory Guard" is set to "On" (page 60). Sound field parameters y · The default settings are marked with "*". CINEMA DSP basic parameters DSP Level Adjustable range: ­6dB to 0dB* to +3dB 1 2 3 4 Turn on the video monitor connected to this unit. The GUI screen appears on the video monitor. Press jCursor n to select "Setup" and then press jENTER. Press jCursor k / n to select "DSP Parameter" and then press jENTER. Sound field program Fine adjusts an effect level (level of the sound field effect to be added). A dead sound field is created when the attenuation time is short while a lively sound field is created when the attenuation time is long. Source sound Level Level ADVANCED OPERATION ADDITIONAL INFORMATION Live Reflecting Level Level Dead Small = 1ms Large = 99ms Time Time y · We recommended that you adjust the size of corresponding sound field when you adjust the delay time. Parameters for specifying room size Small reflected sound Large reflected sound Room Size / P. Back Room Size Adjustable range: 0. 1 to 2. 0 APPENDIX Produces different senses of sound expansion according to room sizes specified. In a large size room such as a music hall, the duration from when reflected sound is heard until when the next reflected sound is heard is long. Thus, different senses of sound expansion can be created by changing the duration. When this parameter is set to 2. 0, each side of the room is defined as twice larger than the original room size. Small = 0 Large = 10 English 51 En Editing surround decoders/sound field programs Parameters for adjusting reverberant sound Reverb Level Adjustable range: 0 to100% Reverb Time Adjustable range: 1. 0 to 5. 0s Reverb Time parameter adjusts the attenuation time of the rear reverberant sound based on the time that about 1kHz reverberant sound takes for 60dB of attenuation. Reverberant sound attenuates faster as you decrease the value. Reverb Time adjustment allows you to create a natural reverberant sound, by setting the attenuation time longer for a sound source or room with less echo, or shorter for a sound source or room with more echo. Rear reverberation Source sound Rear reverberation Reverb Level parameter adjusts the reverberation sound level. Increasing the value of Reverb Level makes the reverbration sound level higher, which allows you to create more echo. Source sound Level (dB) Reverb Level Early reflections 60dB 60dB Time Time Reverb Time Short reverberation Reverb Time Long reverberation Time Parameters for certain sound field programs Parameter for MOVIE sound field programs PLIIx Movie (PLII Movie), Neo:6 Cinema Decode Type Sound source Choices: Small = 1. 0s Large = 5. 0s Selects the decoder type for use with the MOVIE sound field programs. Note · You cannot select a decoder for the following MOVIE sound field programs. ­ Mono Movie ­ Sports ­ Action Game ­ Roleplaying Game Reverb Delay Adjustable range: 0 to 250ms Reverb Delay parameter adjusts the time difference between the beginning of the direct sound and the beginning of the reverberation sound. The larger the value, the later the reverberation sound begins. [. . . ] 64 VIDEO (VIDEO AUX) jack, front panel . . . . . . . . 4 VIDEO jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Video jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Video Out, Option menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]