User manual YAMAHA CP70B

[. . . ] Although StageMix is focused on the requirements for adjusting monitor mixes on stage, its range of features is continually expanding, allowing it to be used for a wider variety of remote control functions. Yamaha Commercial Audio CL StageMix V3. 0 User Guide CONTENTS 1. 0 2. 0 3. 0 System Requirements Wi-Fi Settings Getting Started 3. 1 CL series Network Setup 3. 2 iPad Wi-Fi Settings 3. 3 StageMix Setup 3. 3. 1 OFFLINE DEMO Mode 3. 3. 2 Configure StageMix to Work with a CL Series Console 3. 3. 3 Select a Mixer and Begin Working 3. 3. 4 Edit Mixer Configurations Mixer Window 4. 1 Channel Bank Navigation 4. 2 Layer Navigation 4. 3 Channel Names and Colors 4. 4 Faders 4. 4. 1 Long Faders 4. 4. 2 Navigation in Long Faders Mode 4. 5 Channel ON 4. 6 CUE 4. 7 Master Bank 4. 8 GAIN 4. 8. 1 Digital Gain 4. 8. 2 Gain Compensation Mode 4. 8. 3 ALL GC ON 4. 8. 4 ALL GC OFF 4. 8. 5 Input Port 4. 8. 6 Phantom Power 4. 8. 7 Phase 4. 9 SENDS ON FADERS 4. 9. 1 Mix Send Levels 4. 9. 2 Mix Sends ON 4. 9. 3 Stereo Mix Pan 4. 10 DCA Faders EQ & PAN 5. 1 EQ 5. 1. 1 EQ Curve in Mixer Window 5. 1. 2 Selecting PEQ or GEQ 5. 1. 3 Accessing the EQ Editing Screens 5. 2 PARAMETRIC EQ EDITING 5. 2. 1 HPF 5. 2. 2 EQ Bands 1 & 4 5. 2. 3 EQ ON Page 4 4 5 5 5 6 7 7 8 8 9 9 9 10 10 10 10 11 11 12 13 14 14 14 14 14 14 14 15 16 16 16 17 18 18 18 19 19 20 21 21 22 Page 2 4. 0 5. 0 Yamaha Commercial Audio CL StageMix V3. 0 User Guide 22 22 23 23 23 24 24 24 24 24 24 25 25 26 26 26 28 28 29 29 30 30 30 31 31 31 31 32 33 33 33 33 34 34 34 34 34 34 34 35 35 35 36 36 36 36 Page 3 5. 3 5. 4 6. 0 5. 2. 4 EQ RESET 5. 2. 5 EQ Type GRAPHIC EQ EDITING 5. 3. 1 Navigation in the GEQ Overview Section 5. 3. 2 Rack Position 5. 3. 3 GEQ Type 5. 3. 4 Editing GEQ Bands 5. 3. 5 Navigation in the GEQ Editing Section 5. 3. 6 GEQ ON 5. 3. 7 GEQ FLAT 5. 3. 8 Copy/Paste PAN TO STEREO BUSSES 5. 4. 1 Balance UTILITY 6. 1 Mute Group Masters 6. 1. 1 Mute Group Dim Level 6. 2 Tap Tempo 6. 2. 1 Multi-Select SCENE MEMORY 7. 1 Current Scene 7. 2 Decrement / Increment Scene 7. 3 Scene List 7. 4 Scene Range 7. 5 Selected Scene 7. 6 Store Scene 7. 7 Undo Store 7. 8 Recall Scene 7. 9 Undo Recall SETUP 8. 1 Fader Delay 8. 2 Input Meter Point 8. 3 Output Meter Point 8. 4 Filled EQ Graph 8. 5 Enable Inc/Dec Scene Recall 8. 6 Show Send Levels in Meter Bridge 8. 7 Set EQ band to 0dB with Double-Tap 8. 8 Set DCA to 0dB with Double-Tap 8. 9 Channel Select ­ StageMix Follows Console 8. 10 Channel Select ­ Console Follows StageMix Troubleshooting 9. 1 No Wi-Fi Available 9. 2 Connection Error 9. 3 Connection Lost 9. 4 Graphic EQ Doesn't Affect the Sound 9. 5 Problems Moving Multiple Faders 9. 6 StageMix Facebook Page 7. 0 8. 0 9. 0 Yamaha Commercial Audio CL StageMix V3. 0 User Guide 1. 0 System Requirements Apple iPad (1st generation iPad, iPad 2, or 3rd generation iPad) Yamaha CL series digital mixing console Wi-Fi access point (preferably with 802. 11n, 5GHz capability, though 2. 4GHz and 802. 11g will also work) CAT5 cable (to connect the console to a Wi-Fi access point) 2. 0 Wi-Fi Settings Configure the Wi-Fi access point, following the manufacturer's instructions. No special settings are needed, but using security such as WPA is highly recommended, to prevent unwanted devices from joining the network. Here are some suggested settings to assist less experienced Wi-Fi users: 1. Give the wireless network a name (this is the "SSID"). [. . . ] (In Demo mode, GEQs appear on Mix busses1, 7, 8, 12, 21 and Mono). In the example above: Mix Bus 1 has both PEQ and GEQ available, and GEQ is currently being displayed (the blue dot is solid and the curve is blue). Mix Bus 2 has both PEQ and GEQ available, and PEQ is currently being displayed (the green dot is solid and the curve is green). Page 18 Yamaha Commercial Audio CL StageMix V3. 0 User Guide Mix Busses 3-8 have only PEQ available so no dots are displayed below their EQ curves. 5. 1. 2 Selecting PEQ or GEQ On any channel displaying both a green and a blue dot below the EQ curve, the user can select either of those EQ types to be displayed by using a swipe gesture in the EQ curve area. If a PEQ curve is currently displayed, swiping from right to left will cause the GEQ curve to be displayed. If a GEQ curve is currently displayed, swiping from left to right will cause the PEQ curve to be displayed. 5. 1. 3 Accessing the EQ Editing Screens To access PEQ or GEQ editing, tap on the EQ curve to open the appropriate EQ Editing Screen. If a PEQ curve is displayed, the PEQ editing screen will be accessed. If a GEQ curve is displayed, the GEQ editing screen will be accessed. Note: the EQ editing screen will be accessed when the finger is removed from the curve. Swipe gestures will not cause the Editing screen to be accessed. Page 19 Yamaha Commercial Audio CL StageMix V3. 0 User Guide 5. 2 PARAMETRIC EQ EDITING The current channel's Name, Color, Fader, Level Meters, [ON] and [CUE] buttons are shown in the left column. At the bottom-left, there are "previous" and "next" arrow buttons for navigating to different channels. When one of these bands is selected, the relevant additional buttons are shown above the EQ graph. Page 21 Yamaha Commercial Audio CL StageMix V3. 0 User Guide 5. 2. 3 EQ ON The channel EQ can be switched on/off with the [EQ ON] button towards the top-right of the EQ screen. When the EQ is switched off, the EQ curve will be grey. 5. 2. 4 EQ RESET The [RESET] button above the EQ curve allows the EQ to be reset to either its Default values or to Flat. After pressing [RESET], an "Are You Sure?" popup will be displayed before the action is executed. Selecting "Default EQ" will reset all EQ parameters for the selected channel back to their default values, including HPF. Selecting "Flatten EQ" will set the Gain of bands 1-4 to 0dB, but will not change the Q and Frequency values. Select "No" to cancel and exit this function. 5. 2. 5 EQ TYPE The default EQ Type for every PEQ is Type I. This can be changed to Type II by pressing the [II] button at the top of the EQ editing screen. To exit from the EQ window and return to the Mixer window, press the [MIXER] button at the top-right of the display. Page 22 Yamaha Commercial Audio 5. 3 GRAPHIC EQ EDITING CL StageMix V3. 0 User Guide GEQ Overview In the upper portion of the GEQ Editing Screen, the complete GEQ curve is displayed along with the gain positions for all 31 bands. White dots represent the position for each of the 31 bands. (These dots change to yellow and become larger when they are being touched in the Editing section below. ) The current channel's Name, Color, Fader, Level Meters, [ON] and [CUE] buttons are shown in the left column. [. . . ] Input Meter Point Metering for Input Channels in StageMix can be taken from one of three points in the signal path: 8. 3 Pre HPF Pre Fader Post On 8. 2 Output Meter Point Metering for Output Channels in StageMix can be taken from one of three points in the signal path: Pre EQ Pre Fader Post On Page 33 Yamaha Commercial Audio 8. 4 CL StageMix V3. 0 User Guide Filled EQ Graph When this preference is ON, the EQ graph will be filled in, as it is on the CL series screen. When it is off, only the outline of the graph will be shown. Enable Inc/Dec Scene Recall When this preference is ON, buttons will appear in the Scene Memory screen that allow instant recall of the Next or Previous Scene Memory. Show Send Levels in Meter Bridge When this preference is ON, the send levels for the currently selected "MIX ON FADERS" will appear in the "Navigation/Meter Bridge" in "SENDS ON FADERS" mode. [. . . ]