User manual YAMAHA CRW2100E

[. . . ] FCC INFORMATION COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 714-522-9011 714-228-3913 CD Recordable/Rewritable Drive CRW2100E CRW2100E-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] Refer to the documentation that came with your computer to check whether the computer supports the CSEL function. 7 Setup Flowchart This flowchart shows the procedure for setting up the CRW2100E drive. For easy cross-referencing, the relevant pages in this manual are also given. STEP Connecting the CRW2100E Drive 1. 16) 1 STEP 2 STEP Configuring in the Operating System (P. 24) Check that the CRW2100E drive is recognized correctly. 3 STEP Installing the CD Writing Software For details about how to install the software, refer to the documentation that came with it. Start Using the CRW2100E Drive! Use the drive to create audio CDs, to back up data on your hard disk, or for whatever purpose suits your needs. 4 8 Setup Procedures Serial Number Once you have taken the CRW2100E drive out of its packaging, you should immediately note down the serial number found at the top of the drive with the bar code. You may need to refer to this number when requesting Customer Support services. In the box below the following diagram, write down the 10character serial number (consisting of 3 letters followed by 7 digits). Serial number (3 letters and 7 digits) Serial No. 9 Setup Procedures Connecting the CRW2100E Drive Opening the Computer 1 Power down your computer and unplug it from the AC outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/ or short-circuiting and damaging components, including the CRW2100E drive. 2 Remove the outer casing of the computer. If you need to remove screws in the process, make sure you don't lose them. n The method for removing the casing and fitting the drive in the drive bay can vary depending on the manufacturer. Refer to the documentation that came with your computer for further details. 3 Touch a metal part of the computer's chassis or power supply unit to drain any static charge that may have built up inside your body. Alternatively, you can wear an anti-static grounding (earthing) wrist strap. You can permanently damage equipment if you touch it while there is any static charge in your body. Drain any static charge 10 Setup Procedures Choosing the Connecting Method 4 First make sure how existing IDE devices are connected to your computer, and then determine how to connect the CRW2100E drive in conjunction with those devices. q As an additional drive (set as secondary slave) If the casing of your computer has a spare 5. 25-inch drive bay available, such as with many tower-type designs, you can install the CRW2100E drive in addition to the computer's existing CD-ROM drive. CRW2100E Additional Drive Replacing Drive q As a replacement drive (set as secondary master) If the casing of your computer does not have a spare 5. 25inch drive bay available, such as with many desktop-type designs, you can replace the computer's existing CD-ROM drive with the CRW2100E drive. CD-ROM drive CRW2100E n You cannot replace the computer's existing CD-ROM drive with the CRW2100E drive using the existing cable if the drive is a SCSI type. In this case, use an IDE cable to connect the CRW2100E drive. 11 Setup Procedures 5 Remove the front cover of a vacant 5. 25-inch drive bay slot in the computer. n When you finish this step, proceed to Step 8 on page 15. Additional Drive Front panel to page 15 8 5. 25-inch drive bay slot Front cover 5 Remove the front panel of the computer. Front panel Replacing Drive 12 Setup Procedures About IDE 1 IDE (Enhanced IDE/E-IDE) is one of the standards applied to the connection between personal computers and their peripherals. A computer motherboard provides two IDE connectors (primary and secondary). (Although, some motherboards provide only a primary connector. ) You may connect up to two IDE devices (hard disk, CDROM, or CD-R drives) to the connectors using an IDE cable. One of the devices connected via the IDE cable is called "master" and the other called "slave. " Additional Drive IDE connectors on the motherboard PRIMARY IDE IDE cable (primary) IDE device (slave) IDE device (master) SECONDARY IDE IDE cable (secondary) IDE device (slave) IDE device (master) 6 Disconnect all the cables connected to the rear of the existing CD-ROM drive, and also disconnect the audio cable from the sound card or motherboard's audio connector. n The existing CD-ROM drive in the computer is assumed to be an IDE-type. Replacing Drive Audio cable ANAL OG AUDI O R GG L CABL E SLAV SELECT E MAS TER 39 40 HOST INTE RFAC E 1 2 PO +5V WER GG +12 V IDE cable 4-pin power connector 13 Setup Procedures About IDE 2 Yamaha recommends one of the following connections. Example-1: As secondary slave IDE cable (primary) Hard Disk (slave) Hard Disk (master) IDE cable (Secondary) Connect CRW2100E Additional Drive If you disconnect the IDE device and re-connect it to another location, other devices connected to the IDE cable may become slow in processing, unstable, or inoperative. If the 40-pin IDE cable has only one connector available but you wish to re-connect the IDE device (that you just disconnected) to another location, use a 40-pin IDE cable that has two connectors. If you connect only one IDE device to an IDE cable, assign the device as a master and connect it to the end of the cable. Connect CD-ROM Drive etc. (master) (slave) Example-2: As secondary master CD-ROM Drive etc. IDE cable (primary) (slave) Hard Disk (master) IDE cable (Secondary) No Device (slave) CRW2100E (master) n The CRW2100E drive is shipped with the SLAVE setting. Reset to MASTER if you connect the drive solely to the secondary IDE cable. 7 Remove the four screws holding the CD-ROM drive in place, then slide the drive forward and out of the drive bay. Before removing the CD-ROM drive from the computer, make sure that all the cables have been removed from the CD-ROM drive's rear panel. n Do not force pulling or apply excessive force to the CD-ROM drive. Replacing Drive 14 Setup Procedures Setting the Jumper Switches 8 Set the CRW2100E drive as master or slave to meet your computer environment by plugging the included plastic shunt to the appropriate jumper switch on the rear panel of the CRW2100E drive. n The CRW2100E drive is shipped with the SLAVE setting. Thus, you do not reset the factory setting if you plan to use the CRW2100E drive as slave. If you connect the drive solely to the secondary IDE cable or replace the drive with an existing master device, you need to set the CRW2100E drive as master. from page 12 5 Rear Panel AUDI OO UT DIGIT AL ANAL OG DG RG L CSEL SLAV MAS E TER 1 IDE INTE RF CONN ACE ECTO R DC IN PU T +5V G+ 12V RGL CSEL SLAVE MASTER Plastic shunt IDE INTERF CONNE D 1 +5V SLAVE (factory setting) Jumper switches n The plastic shunts actually contain metal for bridging the two pins of a jumper switch, creating an electrical connection between them when attached. When removed, the jumper switch is set to "OFF Store . " unused plastic shunts in a safe place where they will not be lost. Use a pair of long-nosed pliers to attach or detach the plastic shunts accordingly. However, make sure that the computer is switched off when doing so. 15 Setup Procedures Installing the CRW2100E Drive 9 Slide the drive backwards into the slot. n Do not apply excessive force when sliding the drive back into the drive bay slot. Additional Drive 9 Slide the CRW2100E drive backwards into the nowvacant bay without applying excessive force. Replacing Drive 16 Setup Procedures ) Leave enough room behind the drive to connect the power, IDE and audio cables. Then tighten the four fastening screws on the sides of the unit by hand to hold the drive in place. Additional Drive ) Leave enough room behind the drive to connect the power, IDE and audio cables. [. . . ] 9 Session-at-Once (SAO) . . . . . . . . . . . . . . . . . . . . . . . 32 shunt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SLAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 13, 15 sound card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]