User manual YAMAHA CRW2100IX

[. . . ] FCC INFORMATION COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 714-522-9011 714-228-3913 CD Recordable/Rewritable Drive CRW2100IX This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] After properly installing the software, you are ready to connect the devices. For information about how to install the software, refer to the documentation that came with it. If your computer has no built-in IEEE1394 port, you will first need to install an IEEE1394 interface card (purchased separately). For information about how to install the card, refer to the documentation that came with it. 1 Make sure that the computer is turned on. 2 Make sure that the drive is turned OFF (the POWER switch is not depressed). Power ON Power OFF 3 Connect the supplied power cable to the AC IN socket on the drive's rear panel. 10 Setup Procedures 4 Connect the other end of the power cable to an AC outlet. n The power unit inside the CRW2100IX will automatically adjust itself to the local voltage (100 to 240 volts). 5 Press the POWER switch on the drive's front panel to turn the unit on. n Confirm that the LED on the front panel flashes green and then shines steady orange a moment after the power switch is turned on. 11 Setup Procedures 6 Connect either IEEE1394 port on the drive's rear panel to an IEEE1394 (FireWire or i. LINK) port on the computer using the supplied IEEE1394 interface cable (with a 6-pin connector at each end). Connection to a PC desktop or tower computer IEEE1394 port IEEE1394 ports IEEE1394 interface cable CRW2100IX rear panel Connection to a PC notebook computer via CardBus card IEEE1394 ports IEEE1394 interface card IEEE1394 ports IEEE1394 interface cable CRW2100IX rear panel 12 Setup Procedures Connection to a Macintosh computer IEEE1394 (FireWire) ports 1 2 1 2 IEEE1394 ports IEEE1394 interface cable CRW2100IX rear panel n You can connect the interface cable to either IEEE1394 port on the CRW2100IX drive. n The IEEE1394 standard defines the maximum cable length of a single interface cable as 4. 5 meters. Bear this in mind if using an interface cable longer than the supplied one. If your computer has a 4-pin IEEE1394 port connector (especially common on notebook computers), use a cable with a 6-pin connector on one end and a 4-pin connector on the other. 6-pin IEEE1394 connector 4-pin IEEE1394 connector 13 Setup Procedures Notes on Connecting IEEE1394 Devices Remember the following notes when connecting the CRW2100IX drive to the host computer along with other IEEE1394 devices. q For optimum performance of writing a CD, connect the CRW2100IX directly or solely to the host computer. q Do not connect or disconnect any IEEE1394 devices while the CRW2100IX is in operation (especially when writing to a disc). q If there is a slower device connected between the host computer and CRW2100IX drive, the data transfer between CRW2100IX drive and the host computer will go slow, which may cause failure in writing a CD. q The IEEE1394 ports on the CRW2100IX drive have 6-pin connectors, but do not supply power (IEEE1394 bus power). q Do not turn off the CRW2100IX drive while its IEEE1394-connected computer is turned on. Otherwise, it may cause malfunctions on your computer or other IEEE1394 devices connected together, depending on the specifications of the IEEE1394 interface card (host adapter) or writing software you are using on the computer. Connecting Multiple IEEE1394 Peripherals Together Connecting in a daisy-chain A single daisy-chain can contain up to 17 devices including the host computer. CRW2100IX A maximum single cable length: 4. 5m Connecting in a tree CRW2100IX An entire system can contain up to 63 devices including the host computer. 14 Setup Procedures Restricted Connections Avoid creating a looped connection that sends data output from a device back to the same device. The illustration below shows an example of such a loop (at the host computer). No Good Connecting and Disconnecting IEEE1394 Devices Connecting Devices Your IEEE1394 devices (including the CRW2100IX drive) are supposed to be connected to an IEEE1394 chain or tree connection even while the host computer is turned on (hot plug). n For more information about a IEEE1394 chain or tree connection, refer to page 14. Disconnecting Devices When you attempt to disconnect an IEEE1394 device while the computer is turned on: q Computers running under Windows 98 Second Edition will freeze. To solve this problem, refer to the "Update Information" document bundled with the product. q Computers running under Windows Me or Windows 2000 Professional allow for disconnection after you complete the "unplugging" procedure properly. q Macintosh computers may show an alert message and allow for disconnection after you properly close the CD writing software and unmount the CD volume from the desktop. n For more information about disconnecting IEEE1394 devices while the computer is turned on, refer to the documentation about your operating system. 15 Setup Procedures Verifying the Hardware Installation After connecting the CRW2100IX drive to the computer (or an IEEE daisy-chain or tree), you can verify that the drive is correctly recognized from your computer. Windows Users Make sure that the CRW2100IX is recognized by the operating system. From the Windows 98 Second Edition's [Start] menu, select [Settings]-[Control Panels] and open the [System] control panel. In the [System Properties] window, select the [Device Manager] tab. If you can find a new CD drive icon (YAMAHA CRW2100E), an IEEE1394 bus controller icon, and an SBP2 icon as shown below, you have successfully installed both the drive and the IEEE1394 interface card as Windows OS recognizes both devices. If the devices are not recognized, read the instructions on p. 12 carefully and redo the setup procedures. This screen shot is from Windows 98 Second Edition. n With Windows Me, you can make sure that the CRW2100IX is recognized with the same method as Windows 98 Second Edition. n For details about how to use the operating system, refer to the documentation that came with it. [. . . ] 20 F FireWire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 13 Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 T Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]