User manual YAMAHA CRW2200EZ

[. . . ] (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Electronics Corporation, USA 6660 Orangethorpe Avenue Buena Park, CA 90620 714-522-9105 714-670-0108 CD Recordable/Rewritable Drive CRW2200 CRW2200NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! [. . . ] In this case, use an IDE cable to connect the CRW2200E drive. 13 Setup Procedures About IDE IDE (Enhanced IDE/E-IDE) is one of the standards applied to the connection between personal computers and their peripherals. A computer motherboard provides two IDE connectors (primary and secondary). (Although, some motherboards provide only a primary connector. ) You may connect up to two IDE devices (hard disk, CD-ROM, or CD-R drives) to the connectors using an IDE cable. One of the devices connected via the IDE cable is called "master" and the other is called "slave. " Slave Motherboard Primary Master Secondary Slave Master Notes · When you are using the IDE device as a master, connect the device to the connector of the leading edge of the IDE cable, or you are using the device as a slave, connect the device to the connector of the middle of the IDE cable. · When you connect two IDE devices to one IDE cable, assign each as MASTER or SLAVE respectively. The CRW2200E drive is shipped with the SLAVE setting. Typical IDE-type hardware installation When replacing an existing IDE-type drive to another Controller Port, you will need to change the device settings (MASTER/SLAVE). Note For details on settings, refer to the documentation that came with the device or the Manufacturer's Home Page. 14 Setup Procedures Connecting examples Yamaha recommends one of the following connections. Example-1: As secondary slave (For supplemental drive) Hard disk (master) CD-ROM drive etc. (master) Hard disk (slave) CRW2200E (slave) IDE cable (primary) IDE cable (secondary) Example-2: As secondary master (For replacing your existing drive with the unit) Hard disk (master) CRW2200E (master) IDE cable (primary) IDE cable (secondary) To make the best use of the performance of the CRW2200E drive, Yamaha recommends you connect it as a sole secondary master. Note The CRW2200E drive is shipped with the SLAVE setting. Reset to MASTER if you connect the drive solely to the secondary IDE cable. 15 Setup Procedures Notes · When replacing an IDE-type hardware solely to a IDE cable, select master for the drive, and connect it at the end of the cable. · When the operating system starts with the SCSI hard drive, a primary IDE connector may have no IDE devices. In such a case, Yamaha recommends you connect the CRW2200E drive as a primary master. · When you connect the removed IDE-type hardware to the other connector of the cable, some cables may have only one connector. In such a case, use the cable with two connectors. 16 Setup Procedures Setting the Jumper Switches 5 Set the CRW2200E drive as MASTER or SLAVE to meet your computer environment by plugging the included plastic shunt into the appropriate jumper switch on the rear panel of the CRW2200E drive. Rear Panel Master Slave (factory setting) The CRW2200E drive is shipped with the SLAVE setting. Thus, you do not need to reset the factory setting if you plan to use the CRW2200E drive as SLAVE. If you connect the drive solely to the secondary IDE cable or replace the drive with an existing master device, you need to reset the CRW2200E drive as MASTER. Note The plastic shunts actually contain metal for bridging the two pins of a jumper switch, creating an electrical connection between them when attached. When removed, the jumper switch is set to "OFF". Store unused plastic shunts in a safe place where they will not be lost. About CSEL jumper switch If your computer supports the CSEL function, you can plug a plastic shunt into this jumper switch to have the computer automatically select MASTER or SLAVE for the CRW2200E drive. However, we recommend using the MASTER or SLAVE jumper switch because the CSEL function sometimes creates a conflict. Refer to the documentation that came with your computer to check whether the computer supports the CSEL function. Use a pair of long-nosed pliers to attach or detach the plastic shunts accordingly. However, make sure that the computer is powered down when doing so. 17 Setup Procedures Installing the CRW2200E Drive 6 As a supplemental drive Remove the front cover of a vacant 5. 25-inch drive bay slot in the computer. 5. 25-inch drive bay slot Front cover As a replacement drive Disconnect all the cables connected to the rear of the existing CD-ROM drive, and also disconnect the audio cable from the sound card or motherboard's audio connector. [. . . ] 1 F firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 40 Appendix S SafeBurnTM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 secondary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]