User manual YAMAHA CRW2200IX

[. . . ] (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Electronics Corporation, USA. 6660 Orangethorpe Avenue Buena Park, CA 90620 714-522-9105 714-670-0108 CD Recordable/Rewritable Drive CRW2200IX This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] 19) ¡ Before using the drive, make sure that the drive is recognized by the MacOS and CD writing software on your computer. Start using the CRW2200IX drive Use the drive to create an audio CD, to backup data on your hard drive, or for whatever purpose suits your needs. 12 Setup Procedures Install the CD Writing Software Before connecting the CRW2200IX drive and the computer as described below, make sure that you have installed appropriate CD writing software (¡P. If you use Windows and if the CD writing software is newly installed, first disconnect all IEEE1394 devices from your computer. After properly installing the software, you can connect the CRW2200IX drive. For information about how to install the software, refer to the documentation that came with it. Set Up the CRW2200IX Drive If your computer has no built-in IEEE1394 port, you will first need to install an IEEE1394 interface card (purchased separately). For information about how to install the card, refer to the documentation that came with it. 2 Make sure that the power switch on the rear panel of the CRW2200IX drive is set to STANDBY. 3 Connect the included AC adapter to the DC-IN connector of the drive with the arrow on the adapter plug facing left, as shown below. DC-IN connector Screw Arrow 13 Setup Procedures 4 Connect the included power cable to the AC adapter (). Connect the other end of the power cable to the AC outlet (). Electrical plugs/sockets vary according to country/region. Notes · Operate the drive only with the included AC adapter. · The bottom of the drive and the AC adapter become warm during use. · With the included AC adaptor connected to an AC outlet, even with the power of the drive turned off, power consumption is as shown in the table below. Always unplug the AC adapter from the AC outlet when you do not intend to use the drive for a long time. AC adapter (model) SKB2505A SMB2505A Power source 100 V 120 V 220 ­ 240 V Power consumption 2. 1 W 2. 4 W 1. 4 W 14 Setup Procedures 5 Turn on the CRW2200IX drive. When the power of the CRW2200IX drive is turned on, the power LED on the front panel lights up in green. Power LED LED Note When you turn on the CRW2200IX drive, make sure the LED on the front panel blinks in green, which indicates that it is reading disc information. 33) 15 Setup Procedures 6 Connect either IEEE1394 port on the drive's rear panel to an IEEE1394 (FireWire or i. LINK) port on the computer using the included IEEE1394 interface cable (with a 6-pin connector at each end). Connection to a PC desktop or tower type computer IEEE1394 port IEEE1394 interface cable IEEE1394 ports CRW2200IX rear panel Connection to a PC notebook computer via CardBus card IEEE1394 ports IEEE1394 interface card IEEE1394 ports IEEE1394 cable CRW2200IX rear panel 16 Setup Procedures Connection to a Macintosh computer IEEE1394 (FireWire) ports IEEE1394 ports IEEE1394 interface cable CRW2200IX rear panel Notes · You can connect the interface cable to either IEEE1394 port on the CRW2200IX drive. · The IEEE1394 standard defines the maximum cable length of a single interface cable as 4. 5 meters. Bear this in mind if using an interface cable longer than the included one. If your computer has a 4-pin IEEE1394 port connector (especially common on notebook computers), use a cable with a 6-pin connector on one end and a 4-pin connector on the other. 6-pin IEEE1394 connector 4-pin IEEE1394 connector 17 Setup Procedures Configuring for the Operating System After connecting the CRW2200IX drive to the computer (or an IEEE daisy-chain or tree), you can verify that the drive is correctly recognized by your computer. Windows Users For Windows 98 Second Edition/Me Open "Control Panel" and double-click on the "System" icon. Select the "Device Manager" tab. If you can find a new CD drive icon (YAMAHA CRW2200E), an IEEE1394 bus controller icon, and an SBP2 icon as shown below, you have successfully installed both the drive and the IEEE1394 interface card as Windows OS recognizes both devices. If the devices are not recognized, read the instructions on P. 17 carefully and repeat the setup procedures. * This is a screen shown in the Windows Me environment. For Windows 2000 Professional You can verify by opening "Control Panel, " double-clicking on "System, " selecting the "Hardware" tab, and clicking on the "Device Manager" button in "System Properties. " Notes · For details about how to use the operating system, refer to the documentation that came with it. · If there is an or mark, etc. , next to the icon for the CRW2200IX drive or the IEEE1394 bus controller, this means that it has not been installed correctly. In either case, the CRW2200IX drive may not work properly. 18 Setup Procedures Macintosh Users 1 Select "Apple System Profiler" from the Apple menu. 2 In the Apple System Profiler window, click the "Devices and Volumes" tab. B A A: Make sure that "fw609e" and "sbp609e" are displayed in the FireWire column, showing that it is recognized by the Mac OS. [. . . ] 1 R Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Running OPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 S SafeBurnTM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]