User manual YAMAHA CRW2216EZ

[. . . ] SERIES User Guide Guide de l'utilisateur Bedienungsanleitung ON/ DISC READ/ WRITE Deutsch Français CRW2216E English COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW2216E CRW2216E-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] Multisession In this mode, data can be recorded to disc in stages (one session at a time). Disc at Once In this mode, data can be recorded to an entire disc in one pass. It is not possible to write additional data later. Session at Once In this mode, data can be recorded to disc one session at a time. To use this mode, your software must support Session at Once recording. Packet Writing This is useful for data back-up. Smaller units of data can be added to tracks. To use this mode, your software must support Packet Writing. The CRW2216E supports both sequential and random packet writing. 2 Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW2216E, make sure that you have all of the items on the list of included items. In order to use the CRW2216E, you will require the following. Computer The following operating environment is required: · An IBM/AT compatible computer with a 100 MHz or faster Pentium CPU · A vacant IDE interface connector · A vacant half-height bay · Windows 95, Windows 98 or Windows NT4. 0(Service Pack 3) · Sufficient hard disk space Note: If you wish to create an image file and write it to a CD-R or CD-RW, you will need approximately 750 MB of free space on your hard disk as work area. Software Use writing software or packet writing software which supports the CRW2216E. For software-related questions, please read the owner's manual for your software. 3 Chapter 1 - System Configuration Tools Phillips screwdriver This is used to remove the cover of your computer, and to install the Yamaha CRW2216E drive. Long nose pliers These are used to insert or remove the jumper pin when setting the MASTER/SLAVE settings of the Yamaha CRW2216E drive. Long nose pliers Phillips Screwdriver Discs s CD-R discs Please use discs that are compliant with Orange Book Part 2. (If you wish to write data at 4X speed, you must use discs which support high-speed writing. ) s CD-RW discs Please use discs that are compliant with Orange Book Part 3. (If you wish to write data at 4X speed, you must use discs which support 4X speed writing. ) Yamaha recommends the following Yamaha CD-RW discs: · CRWM74B4X (120mm, 74 minutes) · CRWM74R4X (120mm, 74 minutes) s Read-only Discs You can use discs with the logo which conform to the Compact Disc Read Only Memory standard (CD-ROM standard, Yellow Book). If you wish to use the audio functions, use discs with the logo, which conform to the Compact Disc Digital Audio standard (Red Book). 4 Chapter 2 - Installing the Yamaha CRW2216E Drive Chapter 2 - Installing the Yamaha CRW2216E Drive MASTER/SLAVE settings Before you install the CRW2216E in your computer, you must make the MASTER/SLAVE setting. This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW2216E drive. Important: When the unit is shipped from the factory, this setting is in the MASTER position. Note: Use long-nose pliers to remove or insert the jumper pin. Rear Panel IDE INTERFACE CONNECTOR AUDIO OUT RGL CSEL SLAVE MASTER 1 +5V DC INPUT G +12V Jumper Switch Enhanced IDE compatible computers normally have two IDE interface connectors; a primary one and a secondary one. Each IDE interface connector of the host computer allows up to two IDE devices to be connected. This means that a total of up to four IDE devices can be connected. Normally, a hard disk is connected to the primary connector, and a CDROM drive is connected to the secondary connector. [. . . ] This technique should be used only as a last resort. You'll need a pin-like object of 2 mm or less in diameter to do this. A straightened paper clip makes an ideal tool. Insert the pin-like tool into the manual eject hole and push gently. [. . . ]