User manual YAMAHA CRW3200E

[. . . ] (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Electronics Corporation, USA. 6660 Orangethorpe Avenue Buena Park, CA 90620 714-522-9105 714-670-0108 CD Recordable/Rewritable Drive CRW3200 CRW3200NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] Refer to the documentation that comes with your computer to find out if it supports cable select (CSEL) function. 15 3 Install the CRW3200E Drive The following describes how to install the CRW3200E drive as an additional drive for example. 1 Secure the installation location. Installing the CRW3200E drive as an additional drive Remove the front cover from the 5 ¼-inch drive bay. Replacing Remove all cables connected to the CD-ROM or other devices to be replaced. Then remove the device itself from the computer. Audio cable IDE cable 4-pin internal power cable Note · Be careful not to damage the various cables connected to the rear panel of the CD-ROM drive. · The audio cable is usually caught by the hook at the top of the connector. Release the hook and remove the connector without using excessive force. · Do not apply excessive force to the CD-ROM drive or cables. · Hold the cable by the connector to remove the cable. Pulling the cable itself with excessive force may damage the wires inside. 16 Preparing the CRW3200E Drive 2 Install the CRW3200E drive carefully into the drive bay and temporarily fasten the screws by hand. Be sure that there is enough space to connect the 4-pin internal power cable, 40-pin IDE cable, and audio cable prior to temporarily fastening the included four screws to the fixed position. Install the CRW3200E drive carefully into the drive bay from the front Note Do not apply excessive force to the CRW3200E drive. 3 Connect the included 40-pin IDE cable. Connect the included 40-pin IDE cable to the IDE connector on the motherboard and the IDE interface connector on the rear panel of the CRW3200E drive. Be sure that the colored wire is connected to the first pin of the IDE connector, as shown in the diagram below. Motherboard IDE connector 40-pin IDE cable provided Colored wire IDE interface connector Colored wire 17 Note · IDE devices supporting Ultra ATA/66 or Ultra ATA/100 do not operate with the included 40-pin IDE cable. Prepare proper IDE cables for those IDE devices. · You can use an IDE cable that supports Ultra ATA/66 to connect to the CRW3200E drive. · Use an IDE cable no longer than 45. 7 cm (18 in. ). · When two IDE devices are connected to one IDE cable, be sure to assign each as master/slave respectively. 4 Connect an audio cable if necessary. The sound card of the computer enables you to listen to audio CDs played back on the CRW3200E drive. There are two methods to connect the CRW3200E drive and the sound card: analog connection and digital connection. Audio CD playback · Audio is available from the headphones or speakers connected to the headphone jack on the front panel of the CRW3200E drive (this is convenient for the computer without a sound card). In such a case, connecting an audio cable is not required. · An audio cable is not required to extract an image file from an audio CD since data is transferred via the IDE cable. · If the CRW3200E drive is installed as an additional drive and the CDROM drive or DVD-ROM drive is already connected to the sound card, Yamaha recommends that audio CDs be played back by the existing drive. Continued on next page 18 Preparing the CRW3200E Drive Analog connection Connect one end of the included audio cable (the end with one connector) to the analog audio output jack on the rear panel of the CRW3200E drive. Be sure that the connector is in the correct direction prior to connecting it. There are two types of connectors at the other end of the audio cable. Select the one that fits the sound card: Vertical connector (PH) and Horizontal connector (MPC). Check the direction of the connector vertically and horizontally prior to connecting it to the sound card. [. . . ] This method enables you to add data into the same disc, one session at a time, as long as there is free space available on the disc. A disc that contains data written in several sessions by this method is defined as a multi-session disc, like a disc written by the Track-at-Once method. 39 Packet Writing This method is used to record data onto a disc on a file-by-file basis. This method divides a track into small segments called "packets" so that data can be written on a packet-by-packet basis, which means that you can write data in much the same way as you copy data to a floppy or hard drive. Since the data can be written easily, packet writing is proper to daily data backup. [. . . ]